User manual ZANUSSI ZRT16JD

[. . . ] ZANUSSI KØLESKAB KOELKAST REFRIGERATEUR KÜHLSCHRANK REFRIGERATOR ZRT 16 JC BRUGSANVISNING GEBRUIKSAANWIJZING MODE D`EMPLOI GEBRAUCHSANLEITUNG INSTRUCTION BOOK 200380269 DK NL FR DE GB B/Za/19. (05. ) GB Before installing and using the appliance read this user's instruction book carefully. It contains safety precautions, hints, information and ideas. If the refrigerator is used in compliance with the instructions written, it will operate properly and provide you with greatest satisfaction. [. . . ] Remaining small ice and frost stains on back plate of the cooling compartment after defrosting period is not abnormal. Regular cleaning It is recommended to wash the inside of the refrigerator in 3-4 weeks time. Household cleaner or soap must not be used. After you made it no-current wash the appliance using lukewarm water and wipe it. Clean the magnet door rubber profile with clean water. After cleaning plug the appliance to the mains socket. Dust and dirt collected on the back of the refrigerator, condenser is recommended to be removed and clean the evaporative tray on top of the compressor once or twice a year. When the refrigerator is not in use In case the appliance will not be used for a long time follow these steps: Break the circuit of the appliance. Leave the door open to avoid a build up of air inside. 50 GB Trouble shooting How to change the bulb Should the light fail to work you can change it as below: Break the circuit of the appliance. Unscrew the plate screw fixing the lamp cover, then take the lamp cover off in the direction of arrow and the bulb can be changed. (Type of the bulb: Mignon 322, 230 V, 15 W, E 14 thread) After changing bulb replace the lamp cover, screw the plate screw and apply voltage to the appliance. The lack of light does not influence operation of the refrigerator. If something does not work During operation of the appliance some smaller but annoying trouble can often occur, which does not require calling a technician out. In the following chart information is given about them to avoid unnecessary charges on service. We draw your attention that operation of appliance goes with certain sounds (compressor- and circulating sound). This is not trouble, but means normal operation. We draw it to your attention again that the appliance operates discontinuously, so the stopping of compressor does not mean being nocurrent. That is why you must not touch the electrical parts of the appliance before breaking the circuit. Problem The appliance does not cool sufficiently Possible cause Thermostatic control is set too low. Too many foods to be cooled were put in. There is no inside cool air circulation. The thermostatic control is set too high. Plug is not connected to the mains socket properly. There is no voltage in the mains socket. Thermostatic control is in "0" position. Solution Set higher position. Check if the appliance stands stable (all the four feet should be on the floor). The appliance cools too hard The appliance does not cool at all The appliance is noisy The appliance is not supported properly. Inasmuch as the advice does not lead to result, call the nearest brand-mark service. Instructions for the Installer Technical data Model Gross capacity (l) Net capacity (l) Width (mm) Height (mm) Depth (mm) Energy consumption ZRT 16 JC Fresh food comp. : 159 Fresh food comp. : 148 550 850 600 0, 41 150 A 90 34 (kWh/24h) (kWh/year) Energy class, according to EU standards Roted power (W) Weight (kg) 51 GB Installing the appliance Transportation, unpacking It is recommended to deliver the appliance in original packaging, in vertical position considering the protective warning on packaging. [. . . ] The statutory warranty does not apply when defects are caused by: a chemical or electrochemical reaction caused by water, abnormal environmental conditions in general, unsuitable operating conditions, contact with harsh substances. The guarantee does not apply to defects due to transport which have occurred outside of our responsibility. Nor will the guarantee cover those caused by inadequate installation or assembly, lack of maintenance or failure to respect the assembly instructions or directions for use. Defects that result from repairs or measures carried out by people who are not qualified or expert or defects that result from the addition of non-original accessories or spare parts are not covered by the guarantee. [. . . ]