User manual ZANUSSI ZSF2400

[. . . ] D I S H WA S H E R ZSF 2400 822 61 11-28 INSTRUCTION BOOKLET Contents For the user Important safety information Description of the appliance - General cleaning - Rinse aid dispenser - Spray arm - Coarse filter - Fine filter - Detergent dispenser - Water softener - Water softener plug - Cleaning the cabinet For the installer 3 4-5 Technical specifications Unpacking the machine - If the machine is damaged - Use - Protecting the machine against freezing 12 13 Installation - Water inlet - Water drainage - Power supply 14-15 The control panel How to load the dishwasher -Instruction for test centres 6 7 8 9 10 Using your appliance Something Not Working?Service - Service and Spare Parts - Customer Care Department Guarantee Conditions 11 Guide to use the instruction book The following symbols will be found in the text to guide you throughout the instructions: Safety information Step by step instructions Hints and tips Environmental information -2- Important safety information Before installing and first using the dishwasher, read the instruction booklet carefully, including its hints and warnings. Doing so will ensure that your machine will perform properly and to best advantage. Anyone using the machine should be thoroughly familiar with its instructions for use and safety features. [. . . ] If your water is harder than this, you can increase the capacity of the water softener by pulling out the rubber plug at the rear of the dishwasher on the left hand side viewed from the back. Contact your local Water Authority to find the exact water hardness level for your area. Never run the dishwasher without salt in the container as this may damage the water softener. If the damage is slight, the water softener function can be partially restored by filling the container with salt and then running the Normal cycle 4-5 times. 7 -5- The control panel 1 4 3 2 1 Temperature selector 55° - Button in 65° - Button out Wash phase 2 Programme knob To start the machine: Turn the selector knob clockwise to the programme start. The On/Off switch is built into the programme timer. To isolate the dishwasher from the mains completely, unplug it from the wall socket. During the water heating process, the timer is standing still. Rinse phase Door lock Press the handle down and open the door. Avoid opening the door while the machine is running, steam and hot water could escape from the machine which may cause an injury. If the door is opened slightly after a completed programme the dishes will dry faster. 3 Indicator lamp While the programme is in progress, the indicator lamp is lit and it goes out when the programme has finished. 4 Salt indicator lamp The operating lamp indicates when the salt needs to be replenished. The lamp may remain lit for one or more programmes after refilling the salt container, this is normal. -6- How to load the dishwasher The illustration shows the machine loaded with five place settings. Your own dishes are not likely to be identical to this load, but if you follow the advice below we are sure you will be pleased with the results. · Always place glasses, cups and bowls upside down. · Incline deep dishes (soup plates etc. ) so that the water can run off when drying. (See "How to load the dishwasher"). 15 g detergent into the detergent dispenser. Start the dishwasher by turning the programme knob to the start position. Check the filters to see whether they need cleaning when the dishwasher has finished the wash. Detergent recommendations For best results we recommend the use of Finish detergents, rinse aid and salt. A complimentary sample pack is included in your new dishwasher. -8- Something Not Working? Before calling out an engineer, please check through the details below because some faults can be rectified easily without the need to call out an engineer. If an engineer is called to resolve a problem listed below or to repair a fault caused by incorrect installation or mis-use a charge will be made, even if the appliance is under guarantee. Fault The machine will not start. Check s Is the door closed properly?s Have you set the programme knob properly?s Is the water tap turned on? The machine is not filling with water. s Is the water tap turned on?s Has your domestic water supply been cut off temporarily?s Is the water intake hose kinked or squashed? [. . . ] If it is too short, the entire hose must be replaced with a longer high-pressure hose, specially designed for the purpose. The end of the hose, which is connected to the dishwasher can be turned in any direction. Loosen the retaining nut, turn the hose, then retighten the nut. Check that the nut and all other connections are tight before the machine is moved into position. [. . . ]