User manual ZANUSSI ZT51RL

[. . . ] REFRIGERATOR ZT 51 RL INSTRUCTION BOOKLET 2222632-23 CONTENTS Instructions for the User Important Safety Instructions Description of the Appliance Operation Before use Setting the temperature Fresh food refrigeration Instructions for the Installer 3 4 5 5 5 5 Technical Specifications Installation Positioning Door Reversal 12 12 12 13 Electrical Connection 14 Health and safety guidelines Defrosting Normal Operating Sounds 6 7 7 Maintenance and Cleaning Internal cleaning External cleaning Changing the light bulb When the appliance is not use 8 8 8 8 8 Something not Working?Service and Spare Parts Customer Care Department Guarantee Conditions 9 10 10 11 2 IMPORTANT SAFETY INSTRUCTIONS These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Prior to Installation s Child Safety s Check the appliance for transport damage. [. . . ] Regularly check the refrigerator door seal to ensure that it is clean and free from debris. Always wash your hands with soapy water and dry them with a clean towel before handling food. Keep work surfaces clean and avoid cross contamination by not using the same work surface or knife, without washing them thoroughly in between. s s s s s s s s s 6 DEFROSTING The refrigerator automatically defrosts every time the compressor stops. The water is discharged, via the pipe, into a tray located at the back of the appliance above the compressor, where it evaporates. Important To avoid defrost water overflowing into the fridge, periodically clean the water discharge hole in the centre of the V shaped drip collector at the back of the refrigerator compartment behind the fruit and vegetable drawers. Use the special cleaner provided which you will find already inserted into the discharge hole. D037 Normal Operating Sounds You may hear faint gurgling or bubbling sounds when the refrigerant is pumped through the coils or tubing at the rear, to the cooling plate. When the compressor is on, the refrigerant is being pumped round, and you will hear a whirring sound or pulsating noise from the compressor. A thermostat controls the compressor, and you will hear a faint `click' when the thermostat cuts in and out. 7 MAINTENANCE AND CLEANING Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply. When the appliance is not in use When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods and clean the appliance, leaving the door ajar to prevent unpleasant smells. Internal cleaning Clean the inside and accessories with warm water and bicarbonate of soda (5ml to 0. 5 litre of water). NEVER USE DETERGENTS, ABRASIVE POWDERS, HIGHLY PERFUMED CLEANING PRODUCTS OR WAX POLISHES, TO CLEAN THE INTERIOR AS THESE WILL DAMAGE THE SURFACE AND LEAVE A STRONG SMELL. Clean the drain hole of the water trough at regular intervals and make sure that the drain hole is never obstructed, so that the defrost water may flow freely. External cleaning Wash the outer cabinet with warm soapy water. Once or twice a year dust the condenser (black grill) and the compressor at the back of the appliance, with a brush or vacuum cleaner, see the figure. You MUST ensure that the appliance is switched OFF. An accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption. D662 CONDENSER DEFROST TRAY COMPRESSOR Changing the light bulb Should the interior light fail to work, first switch off the appliance and disconnect from the electricity supply, then replace the bulb as follows: unscrew the light cover and then pull it outward by pressing as shown in the figure. Unscrew the bulb and replace it with a new 15 watt bulb (available from your nearest Zanussi Service Centre). Replace the light cover by sliding it into its original position and replacing the screw. D411 8 SOMETHING NOT WORKING? Before contacting your local Service Force Centre check the following points. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Symptom Solution No power to appliance - Check there is power at the socket. - Check there is not a power cut by checking the household lights. - Check the fuse has not blown. The light does not come on - Ensure that the bulb is correctly fitted. - Check the door light switch is not jammed. - Check the ambient temperature is within the appliances operating limits of 10°C to 32°C. - Check the thermostat is turned to the correct setting relative to ambient conditions. - Adjust the thermostat to give correct temperature control. [. . . ] Unscrew the top hinge pin (2) from the top hinge (1) and replace it in the opposite hole on the left hand side. Unscrew the foot at the base (6) of the appliance and refit it on the opposite side. Refit the door and the bottom hinge to the left hand side. When positioning the bottom hinge blade on the reverse side, the securing screws will require a degree of exersion when fitting. [. . . ]