User manual ZANUSSI ZT695

[. . . ] DISHWASHER ZT 695 COP04 152977 14/2 INSTRUCTION BOOK UK Description of the appliance 1. Levelling spacers Upper basket stop Upper spray arm 1 Salt container Large filter 2 3 13 12 Detergent dispenser Control panel Rating plate Rinse aid dispenser 6 11 4 5 10 10. SID detergent dispenser (Super Intensity Dispenser) 8 9 7 IN72 The control panel In this fully integrated appliance the controls are located on the top of the door. When selecting a programme, the door needs to be open. Intermittent signal "end of programme" An intermittent audible signal informs you that the wash programme has ended. [. . . ] The dishwasher is factory set at level 2. If this level is not suitable for your area the softener should be adjusted. Level 0 1 2 3 4 5 Use of salt NO YES YES YES YES YES If your water is level 0 it is already soft and therefore there is no need to use salt. In this case adjust the water softener on level 1 without using salt. To adjust the water softener With a screwdriver turn the selector on the upper front corner of the machine until the level required corresponds with the marker. 3 4 5 1 2 2 AA05 3 Filling with salt Attention!Only use salt specifically designed for use in dishwashers. All other types of salt not specifically designed for use in dishwasher, especially table salt, will damage the water softener. Only fill with salt just before starting a washing programme. This will prevent any grains of salt or salty water, which may have been spilled, remaining on the bottom of the machine, which may cause corrosion. SR15 1. Unscrew the cap of the salt container. The salt container will require topping up periodically. According to the model, an indicator reminds you when filling with salt: A) The salt cap has a refill indicator window in the centre. A green float is clearly visible when there is salt inside the container, and almost disappears when the salt has finished reminding you to add salt. SR16 2. Pour 1 litre of water inside the container (this is necessary only before filling with salt for the first time). SR11 B) A salt indicator light on the control panel will come on when the salt has finished. SR17 3. Using the funnel provided, pour in the salt until the container is full. The salt indicator light on the control panel can remain illuminated for 2-6 hours after the salt has been replenished, assuming the dishwasher remains switched on. If you are using salts that take longer to dissolve then this can take longer. The function of the machine is not affected. . Do not worry if water over flows from the unit when filling with salt, this is quite normal. SR18 4. Remove any trace of salt on the screw thread or on the gasket. SR19 5. Screw on the cap tightly. 4 Rinse aid Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying. The dispenser, which is positioned inside the door, holds about 110 ml of rinse aid, which is sufficient for 16 - 40 dishwashing programmes, depending upon the dosage setting. Filling with rinse aid 1. Open the container by turning the lid (A) anticlockwise. Add the rinse aid until the container is completely full. The indicator (B) will be completely dark. Top up the rinse aid when the indicator (B) becomes clear. (Only for models with rinse aid indicator light) Top up with rinse aid when the rinse aid indicator light on the control panel illuminates. [. . . ] This will prevent deposits of sand or rust clogging the inlet hose. IN06 IN07 Water outlet hose connection The end of the drain hose can be connected in the following ways: 1. To the sink outlet spigot, securing it if necessary with a clip. Our appliances are supplied with a with a security device to protect against the return of dirty water back into the machine. If the spigot of your sink has a "no return valve" incorporated this can prevent the correct draining of your dishwasher. [. . . ]