User manual ZANUSSI ZU9154

[. . . ] REFRIGERATOR ZU 9154 INSTRUCTION BOOKLET 2222682-31 CONTENTS Instructions for the User Important Safety Instructions Description of the Appliance Operation Before use Setting the temperature Fresh food refrigeration The door shelves Normal Operating Sounds Instructions for the Installer 3 4 4 4 4 4 5 5 Technical Specifications Installation Positioning 13 13 13 Electrical Connection Building-in Instructions Door Reversal Building the appliance in under a worktop Fitting the plinth 14 15 15 17 19 Health and safety guidelines Defrosting Maintenance and Cleaning Internal cleaning Periodic cleaning Changing the light bulb When the appliance is not in use 6 6 7 7 7 7 7 Something not Working?Service and Spare Parts Customer Care Department Zanussi Service Force Guarantee Conditions 8 9 9 10 12 2 IMPORTANT SAFETY INSTRUCTIONS These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Prior to Installation s General Safety s Check the appliance for transport damage. [. . . ] It then took 11 hours to get down to 7°C in the refrigerator. Keep the refrigerator door closed as much as possible. Do not push food together too much, try to allow air to circulate around each item. Cool cooked food as quickly as possible but do NOT place in the refrigerator until cool. (Leave food in a cool place in order that it can then be placed in the refrigerator as soon as possible). Do NOT mix raw and cooked meat, they must be in separate containers. Take care not to let the meat juices drip onto other food. If the meat does drip, remove everything and clean thoroughly. Remove suspect food from your refrigerator and clean (Refer to "Maintenance and Cleaning"). s s Never allow spillages to dry and harden. Store eggs in the egg rack provided in the refrigerator door. Regularly check the refrigerator door seal to ensure that it is clean and free from debris. Always wash your hands with soapy water and dry them with a clean towel before handling food. Keep work surfaces clean and avoid cross contamination by not using the same work surface or knife, without washing them thoroughly in between. s s s s s s s s s DEFROSTING The refrigerator automatically defrosts every time the compressor stops. The water is discharged, via the pipe, into a tray located at the back of the appliance above the compressor, where it evaporates. Important To avoid defrost water overflowing and dripping onto the food in the fridge, periodically clean the water discharge hole (F) situated under the salad drawers. Use the special cleaner provided (P) which you will find already inserted into the discharge hole P F S. I. 011 6 MAINTENANCE AND CLEANING Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply. Warning This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorised technicians. Unscrew the light cover and then pull it outward by pressing as shown in the figure. Unscrew the bulb and replace it with a new 15 watt bulb (available from your nearest Zanussi Service Force centre). Internal cleaning Clean the inside and accessories with warm water and bicarbonate of soda (5ml to 0. 5 litre of water). NEVER USE DETERGENTS, ABRASIVE POWDERS, HIGHLY PERFUMED CLEANING PRODUCTS OR WAX POLISHES, TO CLEAN THE INTERIOR AS THESE WILL DAMAGE THE SURFACE AND LEAVE A STRONG SMELL. Clean the drain hole of the water trough at regular intervals and make sure that the drain hole is never obstructed, so that the defrost water may flow freely. Important Do not use abrasive products. D411 2. [. . . ] Directive: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent amendments. - 89/336 EEC of 3. 5. 89 (Electromagnetic - Compatibility Directive) and subsequent amendments. Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of breakdown. Important The wires in the mains lead are coloured in accordance with the following code: Green and Yellow Blue Brown - Earth - Neutral - Live If you fit your own plug, the colours of the wires in the mains lead of your appliance, may not correspond with the markings identifying the terminals in your plug, proceed as follows: Connect the Green and the Yellow (earth) wire to the terminal in the plug which is marked with the letter «E» or the earth symbol , or coloured green and yellow. Connect the blue (neutral) wire to the terminal in the plug which is marked with the letter «N» or coloured black. [. . . ]