User manual ZANUSSI ZUD9154

[. . . ] REFRIGERATOR ZUD 9154 INSTRUCTION BOOKLET 2222683-22 CONTENTS Instructions for the User Important Safety Instructions Description of the Appliance Operation Before use Setting the temperature Fresh food refrigeration The door shelves Normal Operating Sounds Instructions for the Installer 3 4 4 4 4 4 5 5 Technical Specifications Installation Positioning 13 13 13 Electrical Connection Building-in Instructions Grid preparation Door reversal Building in the appliance under a worktop Fitting the plinth 14 15 15 15 16 20 Health and Safety Guidelines Defrosting Maintenance and Cleaning Internal cleaning Periodic cleaning Changing the light bulb When the appliance is not in use 6 6 7 7 7 7 7 Something Not Working?Service and Spare Parts Customer Care Department Zanussi Service Force Guarantee Conditions 8 9 9 10 12 2 IMPORTANT SAFETY INSTRUCTIONS These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Prior to Installation s General Safety s Check the appliance for transport damage. [. . . ] Store eggs in the egg rack provided in the refrigerator door. Regularly check the refrigerator door seal to ensure that it is clean and free from debris. Always wash your hands with soapy water and dry them with a clean towel before handling food. Keep work surfaces clean and avoid cross contamination by not using the same work surface or knife, without washing them thoroughly in between. s s s s s s s s s DEFROSTING The refrigerator automatically defrosts every time the compressor stops. The water is discharged, via the pipe, into a tray located below the appliance, where it evaporates. Important To avoid defrost water overflowing and dripping onto the food in the fridge, periodically clean the water discharge hole (F) situated under the salad drawers. Use the special cleaner provided (P) which you will find already inserted into the discharge hole P F S. I. 011 6 MAINTENANCE AND CLEANING Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply. Warning This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorised technicians. Unscrew the light cover and then pull it outward by pressing as shown in the figure. Unscrew the bulb and replace it with a new 15 watt bulb (available from your nearest Zanussi Service Force centre). Internal cleaning Clean the inside and accessories with warm water and bicarbonate of soda (5ml to 0. 5 litre of water). NEVER USE DETERGENTS, ABRASIVE POWDERS, HIGHLY PERFUMED CLEANING PRODUCTS OR WAX POLISHES, TO CLEAN THE INTERIOR AS THESE WILL DAMAGE THE SURFACE AND LEAVE A STRONG SMELL. Clean the drain hole of the water trough at regular intervals and make sure that the drain hole is never obstructed, so that the defrost water may flow freely. Important Do not use abrasive products. D411 2. Replace the light cover by sliding it into its original position and replacing the screw. When the appliance is not in use When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods and clean the appliance, leaving the door ajar to prevent unpleasant smells. Periodic cleaning The appliance is equipped with a ventilation grid. Keep clean to guarantee good ventilation and good working order of the appliance. An accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption. The structure of the appliance permits cleaning of the rear zone close to the wall, using a vacuum cleaner. Remove the plinth (1), then the ventilation grid (2); 2. Carefully pull the air deflector out (3), checking that there is no water left from the defrosting. 3 2 1 S. I. 013 Changing the light bulb Should the interior light fail to work, first switch off the appliance and disconnect from the electricity supply, then replace the bulb as follows: 7 SOMETHING NOT WORKING? Before contacting your local Service Force Centre check the following points. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Symptom Solution No power to appliance - Check there is power at the socket. - Check there is not a power cut by checking the household lights. The addresses are listed on the following pages. CUSTOMER CARE DEPARTMENT For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, you are invited to contact our Customer Care Department by letter or telephone or visit our website at www. zanussi. co. uk Customer Care Department Zanussi 55-77 High Street Slough Berkshire SL1 1DZ Tel: 08705 727727 (*) (*) calls to this number may be recorded for training purposes. 9 10 11 GUARANTEE CONDITIONS Standard guarantee conditions We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: s The appliance has been correctly installed and used only on the electricity supply stated on the rating plate. s The appliance has been used for normal domestic purposes only, and in accordance with the manufactuer's instructions. [. . . ] A replacement cover/carrier must be obtained from your local Zanussi Service Force Centre. GREEN & YELLOW 13 AMP. FUSE BLUE D207 CORD CLAMP 14 13 AMP BROWN BUILDING-IN INSTRUCTIONS Before carrying out any work, remove the plug from the power socket. Grid preparation Left door opening: Remove the left side (A) of the grid cutting it from the rear (see figure). A B Right door opening: Remove the right side (B) of the grid cutting it from the rear (see figure). DO002/2 To position the grid on the appliance proceed as follows: Apply the grid to the base of the appliance by pushing the clasps (a) until they click. a a DO001 Door reversal To reverse the opening direction of the door, proceed as shown in the figures: 6 4 1 7 8 5 2 3 1 2 15 Attention After completion of the door reversing operation, check that the door gasket adheres to the cabinet. If the ambient temperature is cold (i. e. in Winter), the gasket may not fit perfectly to the cabinet. [. . . ]