User manual ZANUSSI ZUT113S

[. . . ] ZANUSSI FREEZER ZUT 113S INSTRUCTION BOOK GB 200381028 A/ZE/67. (07. ) This instruction book contains safety precautions, information on use and helpful hints and tips. To ensure you use this appliance effectively and safely, please read this instruction book carefully before installing or using this appliance and retain for future reference. The symbols below help you to find things more easily: Safety precautions Warnings and Safety information Hints, useful information Environmental information The symbol on the product or on its packaging indicates that this product may not be treated as household waste. [. . . ] When you arrive home, place the frozen food in the freezer immediately. Do not push food together too much, try to allow air to circulate around each item. Ensure that food placed in the freezer is dated and labelled and used in date order to ensure that food is consumed at its best. Lean food keeps better and longer than fatty food, salt reduces the storage time. Wrap the food in polythene or aluminium freezing bags or foil so that they adhere to the food and provide an airtight seal. Packaging which is swollen or has traces of refrozen water droplets on the pack could indicate that the product has not been kept at a suitable temperature and that it may have lost its original quality. Partially thawed food must not be refrozen, it must be consumed within 24 hours. Chicken: Should also be cooked and refrozen as a fresh dish. Maint enance & Cleaning Before any maintenance or cleaning is carried out you must DISCONNECT the appliance from the electricity supply. When the Appliance is not in Use When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods and clean the appliance, leaving the door open to prevent unpleasant smells. Internal Cleaning Clean the inside and accessories with warm water and bicarbonate of soda (5 ml to 0. 5 litre of water). NEVER use detergents, abrasive powders, highly perfumed cleaning products or wax polishes to clean the interior as these will damage the surface and leave a strong odour. Defrosting The freezer compartment will become progressively covered with frost. This should be removed with the special plastic scraper provided whenever the thickness of frost exceeds 6 mm (1/4"). During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out and it is advisable to perform this operation when the appliance is empty. External Cleaning Wash the outer cabinet with warm soapy water. Once or twice a year dust the condenser (black grille) and the compressor at the back of the appliance with a brush or vacuum cleaner, as an accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption. 9 To carry out complete defrosting: 1. Disconnect the appliance from the electrical supply. If the plug is inaccessible turn the thermostat control knob to , , 0". Remove any stored food, wrap in several layers of newspaper and store in a cool place. Carefully draw the plastic drain spout out of the lower part of the appliance according to the direction of the arrow and place a tray of a suitable size in the position shown. 5. During defrosting, push the defrost water towards the edge of the cooling plates using a dry cloth or a sponge. It will be collected at the bottom of the appliance, from where it can be diverted into the tray and then disposed of. To accelerate the defrosting process place a bowl of hot (not boiling) water inside the freezer and close the door. When defrosting is completed, dry the interior thoroughly, replace the drain spout and close the door. Turn the thermostat control knob back to a medium setting and leave to run for at least 4 hours with the 'fast freeze' switch on. [. . . ] (07. ) Refit the upper hinge pin into the opposite location. Slot the hinge pin into the hole in the hinge plate and relocate the hinge assembly to the opposite location and refit using the retaining screws. Refit the bottom hinge plate assembly on the opposite side, taking care that the edge of the door is parallel with the side of the cabinet. To reverse the handle proceed as follows: Remove screw covers (if fitted) and handle retaining screws. Remove blanking plugs on the opposite side using a punch. [. . . ]