User manual ZANUSSI ZWC85050W

[. . . ] User Manual Washing machine ZWC 85050 W Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance. The following symbols are used in this manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information Content Safety information - - - - - - - - - - - - - - - - - - -3 Description of the appliance - - - - - - - - - - - -5 Detergent dispenser drawer - - - - - - - - - - - -5 Control panel - - - - - - - - - - - - - - - - - - - - - -6 Display - - - - - - - - - - - - - - - - - - - - - - - - - - -7 Functions - - - - - - - - - - - - - - - - - - - - - - - - -8 Programme table - - - - - - - - - - - - - - - - - -10 Programme information - - - - - - - - - - - - - -12 Washing Hints - - - - - - - - - - - - - - - - - - - - -13 Before the first use - - - - - - - - - - - - - - - - -15 Operating Sequence - - - - - - - - - - - - - - - -16 Care and cleaning - - - - - - - - - - - - - - - - - -19 Something not working - - - - - - - - - - - - - - 21 Technical data- - - - - - - - - - - - - - - - - - - - - 24 Consumption values - - - - - - - - - - - - - - - - 24 Installation instruction - - - - - - - - - - - - - - - 25 Environmental concerns - - - - - - - - - - - - - 28 2 Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. [. . . ] If you have already pressed it, and you wish to cancel the delay time, proceed as follows: · set the washing machine to PAUSE by pressing button 8; · press the button 6 once. On the display will appear the symbol «0'». · press button 8 again to start the programme. · The selected delay can be modified only after you have turned the programme selector dial to the «o» position and after you have selected the programme again. · The door will be locked throughout the delay time. If you need to open the door, you must first set the washing machine to PAUSE by pressing button 8. After you have closed the door, press the button 8 again. The Delay Start cannot be selected with «Drain» programme. Start the programme by pressing button 8 To start the selected programme, press this button; the corresponding green pilot light stops blinking. On control panel the pilot light 9 illuminates to indicate that the appliance starts operating and the door is locked. Altering an option or a running programme It is possible to change some options before the programme carries it out. Before you make any change, you must pause the washing machine by pressing button 8. Changing a running programme is possible only by resetting it. Turn the programme selector dial to «O» and then to the new programme position. Start the new programme by depressing button 8 again. The washing water in the tub will not empty out. Interrupting a programme Press the button 8 to interrupt a programme which is running, the corresponding light starts to flash. Depress the button again to restart the programme. Cancelling a programme Turn the selector dial to «O» to cancel a programme which is running. Opening the door after the programme has started First set the machine to pause by pressing the button 8. If the light 9 goes off, the door can be opened. If it does not switch off, this means that the machine is already heating, that the water level is above the bottom edge of the door. In this cases the door cannot be opened. [. . . ] Check that your domestic electrical installation can take the maximum load required, also taking into account any other appliances in use. Connect the machine to an earthed socket. The appliance is supplied with a 13amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13amp ASTA approved (BS1363/A) fuse must be used. [. . . ]