User manual ZANUSSI ZWG3164

[. . . ] WASAUTOMAAT LAVE-LINGE WASCHAUTOMAT WASHING MACHINE ZWG 3164 COTON/KATOEN Blanc/Witte was Économique/Spaar Blanc - Couleurs/ Witte - Bonte was Blanc - Couleurs/ Witte - Bonte was Blanc - Couleurs/ Witte - Bonte was Synthetica Synthetica Synthetica A B C D F G H J 95° 60° 60° 40° 30° 60° 40° 30° DÉLICATS/FIJNE WAS Délicats/Fijne was Lavage à la main/ Handwas R K 40° L 30° Prélavage Voorwas Court Kort A B C D F Reduction essorage Rinçage + Lage toeren Départ/ Pause Start/ Pauze LAINE/WOL Laine/Wol Laine/Wol Rinçage/Spoelen Vidange/Afpompen Essorage/Zwieren SYNTHÉTIQUES/SYNTHETICA M 40° N P Q R Spoelen + Départ différé 12 H Start uitstel Q 8H 4H 2H P N M L K J H G Fin Einde 1600 rpm ELECTRONIC ZWG 3164 132986310 GEBRUIKSAANWIJZING NOTICE D'UTILISATION GEBRAUCHSANWEISUNG USER MANUAL NL F D GB Dear customer, Please read these operating instructions carefully and pay particular attention to the safety notes indicated in the first pages. We recommend that you keep this instruction booklet for future reference and pass it on to any future owners. Transport damages When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the Service Centre. The symbols you will see on some paragraphs of this booklet have the following meaning: The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly important for your safety or correct functioning of the appliance. [. . . ] Remove persistent stains before washing. Rub particularly soiled areas with a special detergent or detergent paste. Remove hooks or tie them up in a bag or net. Removing stains Stubborn stains may not be removed by just water and detergent. It is therefore advisable to treat them prior to washing. Blood: treat fresh stains with cold water. For dried stains, soak overnight in water with a special detergent then rub in the soap and water. Oil based paint: moisten with benzine stain remover, lay the garment on a soft cloth and dab the stain; treat several times. Dried grease stains: moisten with turpentine, lay the garment on a soft surface and dab the stain with the fingertips and a cotton cloth. 68 ENGLISH 700 g Rust: oxalic acid dissolved in hot water or a rust removing product used cold. Be careful with rust stains which are not recent since the cellulose structure will already have been damaged and the fabric tends to hole. Mould stains: treat with bleach, rinse well (whites and fast coloureds only). Grass: soap lightly and treat with bleach (whites and fast coloureds only). Ball point pen and glue: moisten with acetone (*), lay the garment on a soft cloth and dab the stain. Lipstick: moisten with acetone as above, then treat stains with methylated spirits. Remove any residual marks from white fabrics with bleach. Red wine: soak in water and detergent, rinse and treat with acetic or citric acid, then rinse. Ink: depending on the type of ink, moisten the fabric first with acetone (*), then with acetic acid; treat any residual marks on white fabrics with bleach and then rinse thoroughly. Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste. (*) do not use acetone on artificial silk. Any fabric softener or starching additives must be poured into the compartment marked before starting the wash programme. Follow the product manufacturer's recommendations on quantities to use and do not exceed the «MAX» mark in the detergent dispenser drawer. Quantity of detergent to be used The type and quantity of detergent will depend on the type of fabric, load size, degree of soiling and hardness of the water used. Water hardness is classified in so-called "degrees" of hardness. Information on hardness of the water in your area can be obtained from the relevant water supply company, or from your local authority. Follow the product manufacturers' instructions on quantities to use. [. . . ] · Stubborn stains have not been treated prior to washing. · The correct temperature/programm was not selected. · Excessive laundry load. · The machine vibrates or is noisy: · The transit bolts and packing have not been removed. · The support feet have not been adjusted. [. . . ]