User manual ZEKTOR HDS4

[. . . ] ZEKTOR TM HDS4 Component Video / Audio Switch Owner's Manual www. zektor. com Rev: 9 03/11/2004 Important Safety Instructions! Read all instructions for prior to installation of your product. Retain this User's Manual for future reference. Adhere to all safety and operation instructions. Before cleaning this product, unplug from the wall outlet. [. . . ] STEP 1 1 2 3 4 1 Place the HDS4 in standby mode. This is the factory default mode on power up, and if it has not been changed, you can unplug the HDS4 and plug it back in and it will power up in standby mode (at this point only the power indicator light is lit and glowing RED). If the HDS4 does not power up in standby mode, follow the steps given in "Restoring the HDS4 to Factory Defaults" on page 13. 2 Try different manufacturer codes until one of them causes the IR indicator light on the HDS4 to blink when pressing the POWERTOGGLE key. When found, go to back to "Teaching the HDS4 a new component code" on page 6, to teach the HDS4 to use the new component code. STEP 2 1 2 3 4 7 Learning New Remote Codes Teaching the HDS4 to use new remote control keys If your remote does not have one of the pre-programmed component codes, or you simply want to re-map the HDS4 functions to other keys on your remote, the HDS4 can be taught to use new keys. To teach the HDS4 to respond to new keys, you need to have the remote control(s) you want to use ready, and setup in the manner you want it to be used. STEP 1 1 2 3 4 1 Place the HDS4 in standby mode. This is the factory default mode on power up, and if it has not been changed, you can unplug the HDS4 and plug it back in and it will power up in standby mode (at this point only the power indicator light is lit and glowing RED). If the HDS4 does not power up in standby mode, follow the steps given in "Restoring the HDS4 to Factory Defaults" on page 13. 2 Using a pen or pencil, press and HOLD the SETUP button on the back panel of the HDS4 (located near the power jack) for around 4 seconds, until the HDS4 powers up, and the Power indicator on the front panel of the HDS4 begins to blink GREEN. The HDS4 is now ready to accept new remote control key codes. For each of the following steps: · You may press a key on your Remote Control, if accepted, the IR indicator light will blink, and the key will be learned as the new key for the given function. · Or you may press and release the SETUP key on the back panel of the HDS4, this indicates to the HDS4 to skip this key, and the whatever key was previously programmed for that function will be retained. · Or you may press and hold the SETUP key on the back panel until the HDS4 returns to standby mode. This will end learn mode, all keys already programmed will be remembered, and all the keys skipped will retain their previously programmed values. 3 The Power indicator blinks slowly, and input 1 is selected. STEP 2 1 2 3 4 1 2 3 4 STEP 3 1 2 3 4 Press the key on your remote that you want to use as the new key for SELECTIN1. 1 BLINK 8 STEP 4 1 2 4 The Power indicator blinks slowly, and input 2 is selected. 3 4 Press the key on your remote that you want to use as the new key for SELECTIN2. 1 BLINK STEP 5 1 2 5 The Power indicator blinks slowly, and input 3 is selected. 3 4 Press the key on your remote that you want to use as the new key for SELECTIN3. 1 BLINK STEP 6 1 2 6 The Power indicator blinks slowly, and input 4 is selected. 3 4 Press the key on your remote that you want to use as the new key for SELECTIN4. 1 BLINK STEP 7 1 2 7 After a pause, the Power indicator blinks 2 times, and repeats. 3 4 Press the key on your remote that you want to use as the new key for POWERTOGGLE. 2 BLINKS STEP 8 1 2 8 After a pause, the Power indicator blinks 3 times, and repeats. 3 4 Press the key on your remote that you want to use as the new key for SELECTIN-. 3 BLINKS STEP 9 1 2 9 After a pause, the Power indicator blinks 4 times, and repeats. 3 4 Press the key on your remote that you want to use as the new key for SELECTIN+. 4 BLINKS STEP 10 1 2 10 After a pause, the Power indicator blinks 5 times, and repeats. 3 4 Press the key on your remote that you want to use as the new key for SETDIMMODE. 5 BLINKS 9 STEP 11 1 2 11 After a pause, the Power indicator blinks 6 times, and repeats. 3 4 Press the key on your remote that you want to use as the new key for POWERON. 6 BLINKS STEP 12 1 2 12 After a pause, the Power indicator blinks 7 times, and repeats. 3 4 Press the key on your remote that you want to use as the new key for POWEROFF. 7 BLINKS STEP 13 1 2 3 4 13 The HDS4 will return to the standby mode indicating a return to normal operations. The newly programmed codes will now operate your HDS4. Remote Control Learning Caveats Some remote control codes will work better than others. We've designed the HDS4 to work with a great majority of remote control codes, however a few brands use non-standard ways of transmitting their remote control codes that may not be compatible with the HDS4. · Input 1 selected when powered on. · Auto-dimming mode selected. Changing the HDS4 power on defaults Teaching the HDS4 new power on default settings consists of placing the HDS4 in the preferred initial power on mode, and pressing and releasing the SETUP button on the back panel of the HDS4. STEP 1 1 2 1 Select an initial power on input. 3 4 Using the SELECTIN1 - SELECTIN4 keys, or the SELECT+ or SELECTkeys, choose the desired power on default input. 2 Select the initial Bright / Dim / Auto-dimming mode. STEP 2 1 2 3 4 Using the SETDIMMODE key, choose the desired power on default Bright / Dim / Auto-dimming mode. [. . . ] Set your AV receiver to auto mode so that it will pick the best source of audio. 16 Example 2 Progressive Scan DVD Player with component video output and optical digital audio output Game Console with component video output and optical digital audio output Home Theater PC with RGBHV (VGA) output and coaxial digital audio HDTV Cable with component video ouput, coaxial digital audio output Pr/R Pb/B L/H 1 Toslink Pr/R Pb/B L/H 2 Toslink Pr/R Pb/B L/H 3 Toslink Pr/R Pb/B L/H 4 Toslink Pr/R Pb/B L/H OUT Toslink DC input Y/G SPDIF R/V Y/G SPDIF R/V Y/G SPDIF R/V Y/G SPDIF R/V Y/G SPDIF R/V To AV Receiver/Amp with digital audio input FPTV with component video and RGBHV (VGA) inputs In this component video/VGA mixed application, some input devices are component video, and some are VGA (RGBHV). When selecting the PC on input 4, the projector must also be switched to RGBHV mode, and back to HDTV mode for the other 3 component video signals on inputs 1 to 3. Note: that this can be automated with macro programming on higher end remotes and control systems. 17 Example 3 Progressive Scan DVD Player with component video output and optical digital audio output FPTV with component video and RGBHV (VGA) inputs To AV Receiver/Amp with digital audio input Pr/R Pb/B L/H 1 Toslink Pr/R Pb/B L/H 2 Toslink Pr/R Pb/B L/H 3 Toslink Pr/R Pb/B L/H 4 Toslink Pr/R Pb/B L/H OUT Toslink DC input Y/G SPDIF R/V Y/G SPDIF R/V Y/G SPDIF R/V Y/G SPDIF R/V Y/G SPDIF R/V PLASMA TV with Component Video Inputs RPTV with Component Video Inputs In this output switching application, one DVD player can feed 1 of 4 displays (3 shown here). Since there is only one source of audio, the audio does not need to be switched, and can be routed directly to the AV receiver. 18 Warranty Information Warranty Policy ZEKTOR, LLC warrants this product against defects in material and workmanship under normal use and service for one year from the original date of purchase. [. . . ]