User manual ZEKTOR HDS4.1

[. . . ] ZEKTOR Ho m e T h e a t e r Switches Digital Video / Component Video / Multichannel Audio HDS4. 1 Z E K T OR 1 2 3 4 High Definition Component Video Switch Rev 2 02/22/2006 Contents What's Inside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 An Overview of the HDS4. 1 . . . . . . . . . . . . . . . . 7 Controlling the Front Panel Lights . . . . . 9 Adjusting the Front Panel Intensity . . [. . . ] is now waiting for new IR codes to be sent from your remote control. On your remote control, press the following buttons, in the following order : Step 1: Put the HDS4. 1 into the Setup Mode 1 2 3 4 · · · Once the `' button is pressed. . . . . . the standby LED will flash slower, and all the other LEDs will turn off. Step 2: Select the Intelligent-IRTM Learn Mode Step 3: Teach the HDS4. 1 its new IR codes ZEKTOR Step 3: Teach the HDS4. 1 your new remote control codes · · 1 2 3 4 Power123489 That 's it!will retur n to the state it was in before setup, and will now wor k with your new remote!Power 1-4 8 9 Toggles the HDS4. 's power. (Discrete OFF). POWER 1 4 7 2 5 8 0 3 6 9 Press the following sequence of buttons on your remote control: The new control buttons on your remote are. . . Power123489 That's it!now operates with your new remote control! Note: + _ VOL + _ CH All remote control codes are saved in non-volatile memor y and will not be lost during a power failure. HDS4. 1 Component Video Switch 6 HDS4. 1 Component Video Switch Step 1: Place the HDS4. 1 into the Setup Mode ZEKTOR Controlling the Front Panel Lights There are four different front panel light modes available on the HDS4. . They are: 1 2 3 4 Press and hold the Power Button for 4 secs. The standby LED will blink wildly, and the selection LEDs will start sequencing to the right. Note: · · · · Front panel lights af ter 4 seconds of Front panel lights Front panel lights Front panel lights automatically fade from br ight to dim inac tivit y. are tur ned off. Step 2: Select "Lighting Mode" option ZEKTOR The intensities of the both the br ight and dim levels can be adjusted as well, this is explained in the nex t chapter. To change the front panel lighting mode. . . 4 1 2 3 Step 1: Enter the Setup Mode · · · The HDS4. is placed into the setup mode by pressing and holding the Power button for about 4 seconds. Press the `' button to selec t the "Lighting M ode" option. The front panel selec tion LEDs now indicate the cur rently selec ted light mode as follows: I f `' is lit, then front panel lights are always off. I f `2' is lit, then front panel lights are always dim. I f `' is lit, then front panel lights are always br ight. I f `4' is lit, then front panel lights auto -fade from br ight to dim af ter 4 seconds of inac tivit y. Choose a new light control mode by pressing the associated selec tion button. Press the Power Button to save the new mode and retur n to nor mal operations. After `' is pressed, the standby LED continues to flash, and the front panel will display the current Light Mode setting. Step 2: Select the Lighting Mode option Step 3: Choose a new lighting mode ZEKTOR 1 2 3 4 Step 3: Choose a new lighting mode Auto-Fade Always Bright Always Dim Always Off Exit Setup Mode · · Note: The lighting mode setting is saved in non-volatile memor y and is not affec ted by a power failure. HDS4. 1 Component Video Switch HDS4. 1 Component Video Switch Step 1: Place the HDS4. 1 into the Setup Mode ZEKTOR Adjusting the Front Panel Intensity The br ight and dim levels of the front panel lights of the HDS4. to blend into a wide range of lighting conditions. To change the front panel intensities. . . 1 2 3 4 Press and hold the Power Button for 4 secs. The standby LED will blink wildly, and the selection LEDs will start sequencing to the right. Step 1: Enter the Setup Mode · · · The HDS4. is placed into the setup mode by pressing and holding the Power button for about 4 seconds. Press the `4' button to selec t "Front Panel I ntensit y " option. [. . . ] D. C. HDS4. 1 Component Video Switch HDS4. 1 Component Video Switch Warranty Policy Warranty Policy ZEK TOR war rants this produc t against defec ts in mater ial and wor kmanship under nor mal use and ser vice for t wo years from the or iginal date of purchase. ZEK TOR, at its option, shall repair or replace the defec tive unit covered by this war rant y. I n order to keep this war rant y in effec t, the produc t must have been handled and used as prescr ibed in the instruc tions accompanying this war rant y. This war rant y does not cover any damage due to accident, misuse, abuse, or negligence. [. . . ]