User manual ZEKTOR HDS4X2

[. . . ] Home Theater Solutions HDS4x2 Component Video / Audio Matrix Switch Table of Contents What's Inside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Overview of the HDS4x2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inserting the Remote Control's Battery . 1 2 2 3 3 4 4 4 5 5 Getting Started (Quick Reference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For more information in this setting see the section entitled: "Disabling the remote IR buttons", on page 13. 03 Enable / Disable front panel IR sensor hardware. When disabled, no IR can be received through the front panel IR sensor, the IR jack is not affected. 04 Enable / Disable the rear panel IR jack. When disabled, no IR codes can be received through the rear panel IR Jack, the front panel IR sensor is not affected. Enabling this option requires setting 06 to be disabled. 05 Enable / Disable "Auto on". When enabled, any front panel button press will turn on the HDS4x2. When disabled, only pressing the Power Toggle button (or the and ON buttons on the remote), 1 2 - 8 2 or A - H , if these butwill turn on the HDS4x2. This option does not affect the IR buttons tons are enabled, they will always turn on the HDS4x2. 06 Enable / Disable the "12V on/off control" option. When enabled, and 12V is applied to the IR Jack, the HDS4x2 will power on, when the 12V is removed, the HDS4x2 will power off. Enabling this setting requires setting 04 to be disabled. For more information in this setting see the section entitled: "12V on / off control", on page 25. 07 If set, then video will be muted as well as audio when a mute discrete code is received by the HDS4x2. If reset, then only the audio will be muted when a discrete code, to mute a zone, is received by the HDS4x2. HDS4x2 User Guide, Rev 1. 1, 08-31-07 11 Advanced Control Features Disabling front panel buttons 1 2 3 4 B/A HDS4x2 Enter / Exit 1 setup mode 2 Select "Control settings" Toggle setting on/off 3 4 Select setting To enable or disable the front panel buttons: 1. "Enter the setup mode", by pressing and holding the power toggle button 1 until the display flashes, or by pressing SET and then on the remote. Once the front panel is flashing, press the `2' button 2 , or 3. Use the Zone buttons 4 , to scroll to the 01 setting. Use the Breakaway button 3 , to turn on the RED LED. Press the Power Toggle button 1 , exit the setup mode and return to normal operations, or continue onto the next section entitled: "Disabling individual front panel buttons". NOTE: Even with the front panel buttons disabled, you will still be able to enter the setup mode by holding the Power Toggle button. [. . . ] Wall mount 9V @ 1 . 2A, U . L listed, switching Dimensions . Rack mountable (with feet removed): 17"W x 6. 5"D x 1. 75"H 2 HDS4x2 User Guide, Rev 1. 1, 08-31-07 Warranty Warranty Policy ZEKTOR warrants this product against defects in material and workmanship under normal use and service for two years from the original date of purchase. ZEKTOR, at its option, shall repair or replace the defective unit covered by this warranty. In order to keep this warranty in effect, the product must have been handled and used as prescribed in the instructions accompanying this warranty. This warranty does not cover any damage due to accident, misuse, abuse, or negligence. [. . . ]