User manual ZEKTOR MAS7.1

[. . . ] Home Theater Solutions MAS7. 1 1 2 3 S1 S2 S3 SYNC Multichannel Audio / HDMI Switch Rev 2 07/17/2007 Contents What's Inside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 An Overview of the MAS7. 1 . . . . . . . . . . . . . . . . 3 Rear Panel Connectors . . . . . . . . . . . . . . . . . . . . . . . 7 Using a Different Remote . . . . . . . . . . . . . . . . . [. . . ] In this case we want the MAS7. 1 to turn on and switch to Input when first plugged in. Step 1: Setup the MAS7. 1 to your preferred power on state. · Use the front panel buttons to setup the MAS7. 1 to the op erating settings you'd like at initial power up. While continuing to hold the Power button, press and hold the `1' button. Af ter holding both buttons for about `' seconds, the display will blink indicating the new power on defaults have been accepted. You can test the new defaults by either disconnec ting the power supply from the back of the MAS7. 1 or by unplugging the power supply from the wall. The MAS7. 1 will power up into your new power on default state. Step 2: Save the new initial power on state. Step 2: Save the new initial power on state 1. 3. 1 2 3 S1 S2 S3 SYNC Test the new initial power on state · · 1 Start by pressing and holding the Power button. . . 2 3 . . . while continuing to hold the Power button, press and hold the `1' button. After about seconds, the display will flash indicating the new Power On Default state has been accepted. 20 MAS7. 1 Component Video Switch MAS7. 1 Component Video Switch 21 Step 1: Place the MAS7. 1 into the Setup Mode 1 2 3 S1 S2 S3 SYNC Control Functions I f you are using the rear panel IR jack , you might want to disable the IR sensors to prevent use of the remote control. Or if you have a household with young cur ious fingers that likes playing with buttons, you also have the capabilit y of disabling the front panel switches and only operating the MAS7. 1 with a remote. To enable / disable the front panel switches, and other control func tions. . . Press and hold the Power Button until the display goes wild. (About seconds. ) Step 2: Enter the Enable / Disable control state 1 2 3 S1 S2 S3 SYNC Step 1: Enter the Setup Mode · · · · · · · · The MAS7. 1 is placed into the setup mode by pressing and holding the Power button for about seconds. While in the setup mode, press 'S1' to enter the Enable/Disable control state. The cur rent status will be displayed using the front panel LEDs. A lit LED indicates an option is enabled, and an unlit LED indicates disabled. Use Use Use Use Use '1' to enable/disable the IR S ensor hardware. '2' to enable/disable the IR Jack hardware. '' to enable/disable the front panel buttons. 'S1' to enable/disable IR control. 'S2' to enable/disable 12V On/O ff control. Step 2: Enter the Enable / Disable control state After `S1' is pressed, the standby LED continues to flash, and the front panel will display the current settings. Step 3: Enable or Disable control functions Step 3: Enable or Disable control functions 1 2 3 S1 S2 S3 SYNC Note 1: The IR Jack and 12V O n/O ff control func tions are mutually exclusive ( They use the same jack!). Enabling 12V O n/O ff control will disable the IR Jack hardware. Enabling IR Jack hardware will disable 12V O n/O ff control. Note 2: When disabling the IR Jack and IR S ensor, the hardware is disabled. Whereas 'IR Control' enables/disables whether the MAS7. 1 responds to IR signals received. I f the IR S ensor or IR Jack are enabled, and 'IR Control' disabled, IR signals c an still be read through the RS -232 por t, while being ignored by the MAS7. 1. [. . . ] The MAS7. 1 is rack mountable and comes in black or silver. DVI / HDMI Bandwidth: DVI/HDMI Pixel Rate: HDTV Resolutions: HDCP: HDMI Audio: PC Resolutions: Digital Audio Channels Inputs: Outputs: Maximum Transfer Rate: Digital Audio Modes: Coax Input Level Range: Coax Output Level: Control IR Sensor: IR Jack: 12V Control: Serial Port: Power Requirements: Voltage Requirements: Optional International: Adapter Power Supply: Dimensions: Warranty: MAS7. 1 Component Video Switch MAS7. 1 Component Video Switch 7 Warranty Policy Warranty Policy ZEK TOR war rants this produc t against defec ts in mater ial and wor kmanship under nor mal use and ser vice for t wo years from the or iginal date of purchase. ZEK TOR, at its option, shall repair or replace the defec tive unit covered by this war rant y. I n order to keep this war rant y in effec t, the produc t must have been handled and used as prescr ibed in the instruc tions accompanying this war rant y. This war rant y does not cover any damage due to accident, misuse, abuse, or negligence. [. . . ]