User manual ZENITH DVC2200C OPERATING GUIDE

[. . . ] machine number | DVC2200C enjoy the view ® operating guide PAGE 2 INTRODUCTION Safety Precautions WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated `dangerous voltage' within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: CAUTION: ATTENTION: CAUTION: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. [. . . ] If your A/V receiver has a Dolby Pro Logic decoder. Refer to the following connection diagram. DIGITAL OUT AUDIO OUT COAXIAL L R S-VIDEO OUT VIDEO OUT Connect one or two rear speakers. The output sound from the rear speakers will be monaural even if you connect two rear speakers. To VIDEO OUT To AUDIO OUT Video cable Audio cable Connection example Receiver equipped with Dolby Pro Logic Surround To audio input To video input Front speaker (left) TV Center speaker Front speaker (right) Rear speaker (left) Rear speaker (right) q With a receiver equipped with Dolby Digital (AC-3) Connect the equipment the same way as described in "Enjoying Dolby Digital (AC-3) Sound" on the previous page. Refer to that receiver's owner's manual and set the receiver so you can enjoy Dolby Pro Logic Surround sound. Warning Do not set the Digital Audio Output of this DVD player to "Dolby Digital" unless you are connecting the DIGITAL AUDIO jack of this DVD player to an AV decoder that has the Dolby Digital (AC-3) decoding function. High volume sound may damage your hearing as well as the speakers. (Refer to "Selecting Digital Audio Output" on page 37. ) CONNECTIONS PAGE 17 Connecting to Optional Audio System Enjoying 2 Channel Digital Stereo Sound 2 Channel Digital Stereo You can enjoy the dynamic sound of 2 Channel Digital Stereo by connecting this DVD player to a receiver equipped with a digital audio input and speaker system (right and left front speakers). Connection example 75 ohm coaxial cable To digital audio input To S-video Input or Video Input S-Video cable or Video cable To DIGITAL OUT Front speaker (left) Receiver equipped with a digital audio input Front speaker (right) DIGITAL OUT AUDIO OUT TV COAXIAL L R S-VIDEO OUT VIDEO OUT Enjoying DTS Sound Introducing DTS Digital SurroundTM. . . the finest technology ever invented to transform existing "home theater" systems into six discrete channels of exceptionally clear, better-than-compact disc, digital audio performance. And DTS Digital Surround is the only 5. 1 surround sound format that can deliver this revolutionary 3-dimensional experience through new music recordings on compact discs, original 5. 1 soundtracks on motion picture laserdiscs, and soon, a wide variety of products on DVD. 75 ohm coaxial cable Receiver equipped with a DTS decoder To digital audio input Connection example To S-video Input or Video Input To DIGITAL OUT To S-VIDEO OUT or VIDEO OUT DIGITAL OUT S-Video cable or Video cable Front speaker (left) Front speaker (right) Center speaker AUDIO OUT COAXIAL L Sub woofer Rear speaker (left surround) Rear speaker (right surround) R S-VIDEO OUT VIDEO OUT "DTS" and "DTS Digital Out" are trademarks of Digital Theater Systems, Inc. Notes Refer to the owner's manual of your receiver as well. When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections. The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver's volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high volume sound. Turn off the receiver before you connect or disconnect the DVD player's power cord. If you leave the receiver power on, the speakers may be damaged. PAGE 18 BASIC OPERATION Basic Playback This section shows you the basics on how to play back a DVD video disc. Preparations q When you want to play back DVD video discs, turn on the TV and select the video input source connected to the DVD player. q When you want to enjoy the sound of DVD video discs or audio CDs from the audio system, turn on the audio system and select the input source connected to the DVD player. q For connection details, see pages 13 through 17. q Set the playback picture size according to the aspect ratio of the connected TV at the SETUP menu (TV Aspect). q If you do not have the necessary equipment to enjoy Dolby Digital (AC-3) sound, set the Digital Audio Output at the SETUP menu to "PCM". menu search select/enter power open/close play pause/step stop skip scan menu 3 1 4 pause /step setup power dvd vcr catv tv 1 play skip stop select/ enter open/close Press POWER. The DVD player turns on and the power indicator lights up. skip ch vol vol ch return/tv input 2 2 q Press OPEN/CLOSE. The disc tray opens. You can open the disc tray by pressing this button even if the DVD player is in standby mode. display 1 4 7 clear 2 5 8 0 3 sound/mute 3 q Place a disc on the disc tray with the playback side down. There are two different disc sizes. Place the disc in the correct guide on the disc tray. If the disc is out of the guide, it may damage the disc and cause the DVD player to malfunction. Do not place anything except 3" discs or 5" discs on the disc tray. 6 program 9 title menu q angle marker-search a-b random zoom audio subtitle repeat 4 slow/scan rev fwd Press PLAY. The disc tray is automatically closed and playback begins. If the disc is placed in upside down (and it is a single sided disc), "NO DISC" or "DISC ERROR" appears on the TV screen. CD DVD TITLE CHP/TRK PROG. [. . . ] · Turn on the equipment connected with the audio cable. · Set the Digital Audio Output to the correct position, then turn on the DVD player again by pressing the POWER button. · Insert a disc. (Check that the DVD, or audio CD indicator in the DVD display is lit. ) · Insert a playable disc. (Check the disc type, color system and Regional code. ) · Place the disc with the playback side down. [. . . ]