User manual ZENITH MBC4030

[. . . ] I. AUX VIDEO INPUT R - AUDIO - L Typical Jackpack 2 Grasping the removal hook provided firmly, remove the VGA connector card. C O M P U T E R I N Typical Card PAGE 4 206-3492-O Install New Conversion Card CAUTION: Be sure the power cord is disconnected before installing the new conversion card. 3 Align the new scan card edge with the slots in the jack panel, guide the new card into the open slot where the old card was. Push card in firmly enough to be sure it snaps into position. C O M P U T E R I N Typical Card Vid eo Ou t 4 Reinstall the two screws on the jack panel. C O M P U T E R I N Antenna Cable COMPUTER AUDIO INPUT RIGHT LEFT S-VIDEO INPUT R - AUDIO - L LOOP OUT - S-VHS - IN M. P. I. Video Out AUX VIDEO INPUT R - AUDIO - L Typical Jackpack 206-3492-O PAGE 5 Hook Up a Computer to your TV An accessory packet comes with the 46 Series Presentation TVs. cable with a "video-mirror", The cable is used to provide a computer image to two monitors--your computer's monitor and your Zenith Presentation TV. 1 Make the connections with the 15-ft. [. . . ] Also refer to the preceding page for audio connections and "Using the monitor function. " TV Back Note: Actual appearance of components may vary. TV C O M P U T E R I N Connect to Computer PC Connect to TV ANTENNA CABLE S-VIDEO OUT S-VIDEO IN R- AUDIO- L M. P. I. R AUDIO OUT L VIDEO AUX IN R- AUDIO- L Back of Computer R- AUDIO- L COMPUTER AUDIO Video-Mirror cable connectors are clearly marked. Connect as shown in drawing: TV to the television MON to the Computer Monitor PC to the Computer MON Connect to Monitor Video cable from monitor Computer monitor Your TV must be plugged in--not necessarily turned on--for the computer monitor to function. You can "Daisy Chain" other TVs via the S-video loop out and show the computer display on more TV sets. *The Video Mirror Cable is included with Zenith Presentation series TVs. PAGE 6 206-3492-O Hook Up a Computer to your TV After all connections are made, follow instructions below to select Computer source to show your computer's image on the screen 1 2 Make the basic connections as indicated. (Appearance of components may vary from those in the illustrations. ) Plug in your TV. Your Presentation TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC Current. 3 4 On the remote, press TV/VCR SOURCE repeatedly until "REAR COMPUTER SVGA" is displayed. As it warms up, the TV will adapt to your computer. TV back Out to other Monitor C O M P U T E R "Video Mirror" Cable Back of Computer ANTENNA CABLE I N S-VIDEO OUT S-VIDEO IN R- AUDIO- L Video Out Jack Video Out M. P. I. R AUDIO OUT L VIDEO AUX IN R- AUDIO- L R- AUDIO- L COMPUTER AUDIO Components may vary from those in the illustration. If you have a Macintosh, use the 2-row to 3-row DB15 adapter on their video connector. -Install optional PCZ40 Macintosh cable adapter. · Display toggle key set to "Internal". -Locate toggle key and set to "External". PC Computers (Refer to Owner's manual for operating instructions) Computer does not work. · Is proper video format -Select VGA for a PC, see computer selected?· Display toggle key set to "Internal". -Locate toggle key and set to "External". PAGE 10 206-3492-A Computer/PCZTV Loop-Out Setups S-Video Loop-out from Master TV to other TVs After you install the scan conversion card into your 46 Series Presentation TV, you can "daisy-chain" the TV's S-Video or Video output to other TVs: Send the computer image to a "Master" TV and then to other TVs connected in a daisy-chain series Notes · These setups require factory menu item 25 NTSC SCANCARD, default value "0" to be changed to "1". (See your 46 Series Presentation TV's Installation Guide for instructions regarding how to change factory menu item default values. ) · The cables shown in each of these setups are not supplied with the scan card or with the 46 Series, Presentation TVs. See your Zenith dealer to purchase the necessary cables or for further information. Setup for Looping-Out S-Video/Video Computer Image to a Master TV & other TVs 1. With the Computer and TV disconnected from power and the MBC4030 Scan Conversion Card installed, make S-Video or Video connections as shown. Connect Computer and TV(s) to power, first turn on the PCZTV, TVs, and then the Computer. On the PCZTV, select TV source "REAR COMPUTER NTSC OUT" using the TV's Source menu. Back of computer ABC Video cable from monitor Cable for "video mirror" Computer Monitor Computer TV back Computer input to Master TV C O M P U T E R I N ANTENNA CABLE S-VIDEO OUT S-VIDEO IN R- AUDIO- L Actual appearance of components may vary Video Out M. P. I. R AUDIO OUT L VIDEO AUX IN R- AUDIO- L R- AUDIO- L COMPUTER AUDIO Master TV's Computer output to other TVs in the "Daisy Chain" ABC ABC ABC ABC Video Loop-out from Master TV to other TVs Back of computer ABC Video cable from monitor Cable for "video mirror" TV back Computer Computer Monitor SOURCE REAR COMPUTER NTSC OUT PRESS: SOURCE TO CHANGE ENTER TO ACTIVATE Computer input to Master TV C O M P U T E R I N ANTENNA CABLE S-VIDEO OUT S-VIDEO IN R- AUDIO- L Video Out M. P. I. [. . . ] R AUDIO OUT L VIDEO AUX IN R- AUDIO- L Actual appearance of components may vary R- AUDIO- L COMPUTER AUDIO Master TV's Computer output to other TVs in the "Daisy Chain" Viewing Sources Note: Be sure to follow instructions supplied with your computer, and TV(s) for selecting viewing sources. Computer image should appear on your Master and other TVs connected in series. ABC ABC ABC ABC 206-3492-A PAGE 11 PZC3000 Scan Conversion Card Warranty Direct-View Color TV Welcome to the Zenith family!We believe that you will be pleased with your new Zenith TV. Please read this warranty carefully, it is a "LIMITED WARRANTY" as defined under Federal Law. [. . . ]