User manual ZENITH PCZ3000 SETUP GUIDE

[. . . ] · Consult the dealer or an experienced radio/TV technician for help. CAUTION: Do not attempt to modify this product in any way (except as noted herein) without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user's authority to operate this product. PCZ3000-WARN 1/00 Table of Contents The PCZ3000 Upgrade Kit Contains: A-19095 or A-19095-01 206-3705 Scan Conversion Card. Installation and Setup Guide. U p g ra d e s 4 6 S e r i e s P re s e n t a t i o n T M T V s t o 4 7 S e r i e s P re s e n t a t i o n T V s, a l l ow i n g m u l t i - fo r m a t c o m p u t e r connections Safety Warnings . [. . . ] If Zoom Mode is enabled it will cycle through: 1:1, 2:1, 3:1, 4:1, then back to 1:1 etc. PAGE 8 206-3492-A Remote Key Command Functions The table below illustrates the menu structure for your Presentation TV while in Rear Computer mode. As with the Remote Key Command Functions, menus are operated through the NUMBER keypad. Generally speaking, keys 4 and 6 adjust menu options, key 8 cycles through menus and key 5 cancels all operations no matter what menu you are adjusting. Although menus are available in the Advanced mode, adjustments in this mode should only be made by a qualified service representative. A Menu Adjust: H. Soften Off Adjust 8 5 6 Menu Adjust: H. Soften On 4 Adjust 8 Menu Adjust: Advanced . . Adjust 8 5 6 C Menu Advanced: SW 18 HW 6, 5 Adjust 8 5 5 Menu Adjust: Zoom Cont: Remote Adjust 8 5 6 Menu Adjust: Zoom Cont. Menu 4 Adjust 8 Menu Advanced: Total Lines 628 Adjust 8 5 5 Menu Adjust: Zoom Level 2 Adjust 8 5 5 6 Menu Adjust: Zoom Level 3 4 Adjust 8 5 6 Menu Adjust: Zoom Level 4 4 Adjust 8 Menu Advanced: Vert. Freq 60 Adjust 8 5 Menu Adjust: Screen Size . . Adjust 8 5 6 Menu Size: Out H-Center: 77 4 Adjust 8 6 5 Menu Advanced: Sense 2 4 Adjust 8 6 5 Menu Size: Out H-Width: 99 4 Adjust 8 5 6 5 Menu Advanced: CR Character 13 Adjust 8 5 6 Menu Advanced: CR character 130 4 Adjust 8 Menu Size: Out V-Center: 340 4 Adjust 8 5 5 6 Menu Advanced: Clock width 2 4 Adjust 8 6 Menu Size: Out V-Height: 600 4 Adjust 8 Menu Advanced: Clock Width B: 2 4 Adjust 8 6 5 5 Menu Size: Store OK Adjust 8 5 5 6 Menu Advanced: Store Settings 0 4 Adjust 8 6 Menu Adjust: Manual Set . . Adjust 8 5 6 Menu Manual Set: VGA Left: 0 Adjust 8 5 6 B 5 Menu Advanced: Eng Reset Off 4 Adjust 8 6 Menu Manual Set: VGA Width: 80 Menu Manual Set: VGA Bot/4: 157 4 Adjust 8 6 C A 5 4 Adjust 8 6 5 5 Pressing this key will exit all Scan Card Menus. Menu Manual Set: VGA Top/4: 5 4 Adjust 8 6 5 Menu Manual Set: VGA Store 0 Adjust 8 6 5 B PAGE 9 206-3492-A Troubleshooting Troubleshooting Problem Installation Old card is hard to remove. Possible Cause(s) Possible Solution(s) · Screws not removed. · Snug fit. -Remove two screws holding old card in place. -Grasp old card by the hook provided and pull firmly enough to free old card from internal connector. -Be sure card is firmly seated into internal connectors. Green light is not lit when TV power is restored and TV is on. · Card not completely installed. Macintosh Computers (Refer to Owner's manual for operating instructions) Computer does not work. · Is proper video format -Select SVGA for a Macintosh, see computer selected? [. . . ] It is imperative that Zenith know how to reach you promptly if we should discover a safety problem that could affect you. For warranty service information, call 1-888-865-3026. Parts and service labor that are Zenith's responsibility (see above) will be provided without charge. [. . . ]