User manual ZIBRO ARBELLA

[. . . ] ARABELLA 2 6 3 4 > 1 = gEBRAUchsAnWEisUng BRUgsAnVisning MAnUEL D'UTiLisATiOn OPERATing MAnUAL isTRUziOni D'UsO gEBRUiKsAAnWiJzing BRUKsAnVisning 2 18 34 50 66 82 98 iMPORTAnT cOMPOnEnTs A exhaust flue/ chimney (not included in deliVeRy) 2 exhaust flue dampeR (not included in deliVeRy) 3 glass cleaning aiR inlet 4 inspection WindoW 5 6 7 8 9 fiRe heaRth dooR gasket handle ash gRid shakeR pRimaRy aiR inlet contRol J ash pan (Behind dooR) K L M ash pit dooR adJustaBle feet Room aiR ReciRculation sWitch 1. LEggERE DAPPRiMA LE insTRUziOni D'UsO. in cAsO OF DUBBi RiVOLgERsi AL RiVEnDiTORE DELL'APPAREcchiO. 4 50 Dear sir, Madam, Congratulations on the purchase of your Zibro stove. [. . . ] During first heating cycles the coating will harden and the steel will set itself. in order to prevent permanent damage to the stove this initial stoking up must be done gradually and at low fire. Keep this low fire for the first four to five hours after which the capacity gradually can be increased. Keep the stove continuously burning for at least another three to four hours. During first operation it is normal that an unpleasant though non harmful odour will be produced. the above described procedure must be followed for at least the first four times the stove is used. Make sure to ventilate the room sufficiently. D. nORMAL OPERATiOn OF ThE sTOVE to start the stove: Fully open the door and the primary inlet valve (see picture 2) by turning the valve to "+". place and lit some crumpled paper or fire lighter sticks (fire starter sticks) in the fire bed together with some small size dry fire wood (for fuel requirements: see chapter d. 3) do not use liquid fuel, such as for example alcohol, petrol, gasoline etc to start the fire. The flame and performance of the stove can be controlled by moving the primary Picture 2: Primary Air inlet. air inlet valve simply follow the + and signs (see picture 2). When starting the fire the chimney and exhaust flue is still cold, due to which there will only be little draught. Create enough start up draught by keeping the ash pan (little), the stove charging door (little) and the primary air inlet (maximum) open during the first eight to ten minutes. after these eight to ten minutes the fire will burn more extensive, now place bigger fire wood. close ash pan and stove charging door to a minimum. 4 55 After another 10 minutes close the charging door completely. Now close the primary air inlet valve to minimal whilst still ensuring good burning fire (see chapter d. 1. 1. ). G DURing nORMAL OPERATiOn: The primary air inlet valve must be kept to a minimum whilst still ensuring a good burning fire-, this will ensure that the burning process is as clean as possible and the efficiency is as high as possible. The capacity and efficiency of the stove varies with the kind of wood as well as with the wood load. To protect the environment and the complete stove system, do not use: - wood work scraps with glues and/or solvents, - waste wood in general, - cardboard (for start up purposes a minimum of paper may be used only during the starting phase), -painted or impregnated wood, -bonded wood (such chipboard, hardboard, MDF), synthetic fibers. Do not use liquid fuel, alcohol, petrol, gasoline etc. Do not use the stove as a burner for waste materials. the performance of the stove is best using strong, harder wood such as oak, beech, ash and elm. soft woods like pine tree, poplar and linden will result in less performance and possible more residue and soot. G Picture 4: room air circulation switch D. 4 ROOM AiR ciRcULATiOn this stove is provided with a room air circulation fan. When the fan is switched on the room air is drawn across the internal hot surfaces of the stove and due to this warmed up. [. . . ] transportation costs and the risks involved during the transportation of the heater or heater components shall always be at the expense of the purchaser. Stove is installed by a by Zibro agreed installer and the commissioning protocol can be presented. In order to avoid unnecessary costs, we recommend that you always carefully read this manual first. In case they offer no solution, please consult your dealer or installer. * the stove window pane is heat resistant to temperatures above temperatures that can occur in the stove. [. . . ]