User manual ZIBRO PH733

[. . . ] P 720 - P 726 - P 729 - PH 733 2 6 5 3 FIN GEBRAUCHSANWEISUNG BRUGSANVISNING INSTRUCCIONES DE USO MANUEL D'UTILISATION KYTTOHJE OPERATING MANUAL 4 22 40 56 72 88 4 2 ALLGEMEINE SICHERHEIT Aus Sicherheitsgrnden bitten wir Sie, die Bedienungsanleitung vor Inbetriebnahme sorgfltig zu lesen!Personen, die mit der Bedienungsanleitung nicht vertraut sind, drfen das Gert nicht bedienen. Kabel nicht zusammendrcken oder knicken. Nicht vor geffneten Fenstern aufstellen. [. . . ] The expelled air is then as warm as possible. 4 92 COMMENT! The flexible air exhaust hose(s) can be stretched to a length of approximately 1200 mm. The length of these hose(s) was calculated on the basis of the capacity of the device. The use of other hoses or extensions may cause faults in the device. The exhaust air must be able to flow out unhindered. If this is not possible this may lead to overheating or water condensation in the air exhaust hose . This is why you must ensure that there are no kinks or sharp corners in the air hose(s). To obtain an optimum result, the air hoses must be kept shorter than 1 metre while the airconditioner is in use. C OPERATION / REMOTE CONTROL ATTENTION! Avoid the remote control from getting wet. Remove it from the unit when condensation can occur. LCD display On/off Fan speed Function selector switch Down Clock Timer Temperature display selector button (Celsius / Fahrenheit) Up Signal indicator Clock Negative ion function indicator Ventilator speed indicator Function indicator Timer setting indicator Timer on/off Celsius / Fahrenheit control light Temperature setting indicator Symbols: Automatic Cooling Dehumidifying Circulating air Heating (only by PH 733) High ventilator speed Average ventilator speed Low ventilator speed ATTENTION! Without the remote control, the air-conditioner can be operated by using the button on the front of the device. In this event however, only the automatic function can be used. 4 93 PLACING BATTERIES IN THE REMOTE CONTROL Remove the battery cover by pressing the lips in and then pulling the cover toward you. Place the new batteries as indicated (pay attention to the plus- (+) and minus poles (-). Now replace the battery cover. NOTE! Use 2 AAA (1. 5 Volt) batteries. Replace batteries with new batteries of the same type when the display becomes fuzzy or the signal deteriorates. 1 Push the plug into the socket. ATTENTION! If the airconditioner does not respond to the remote control, follow the following procedures: Ensure that there are batteries in the remote control. Ensure that the plug of the airconditioner is inserted in the socket and switched off. Press the on/off button on the unit until you hear a beep (you will hear a beep after 8 seconds). After the beep you can release the button. Briefly press the on/off button of the remote control. The remote control is ready for use after the beep signal. 2 Press the C/F-button to set C (Celsius) or F (Fahrenheit). 3 The following functions can be selected with the mode button remote control. Automatic regulation of ventilator speed Cooling; Dehumidifying; Circulating; Heating (PH733). AUTOMATIC In the automatic mode , the device will cool, dehumidify or heat depending on the ambient temperature. When the temperature in the room changes, the mode changes automatically in order to maintain the desired temperature as accurately as possible. The ventilator speed also adjusts automatically. [. . . ] Clean the filter or replace it (see chapter D). The device works insufficiently. Air inlet or exhaust is blocked. The device is standing on an uneven surface. Remove the blockage. Place the device on an even surface (less vibration). The compressor does not work. Wait 30 minutes until the temperature has dropped The overheating safety and then switch it on feature has been activated. batteries are empty. The remote control does not respond. Restore the connection The signal of the remote control cannot be received between the remote control and the air by the unit. conditioner (see chapter C). Never attempt to disassemble or repair the device. [. . . ]