User manual ZIBRO RS 50 TUONO

[. . . ] RS 50 TUONO use+maintenancebook aprilia part# 8202413 2004 aprilia s. p. a. - Noale (VE) SAFETY WARNINGS The following precautionary warnings are used throughout this manual in order to convey the following messages: Safety warning. When you find this symbol on the vehicle or in the manual, be careful to the potential risk of personal injury. Non-compliance with the indications given in the messages preceded by this symbol may result in grave risks for your and other people's safety and for the vehicle! INFORMATION The operations preceded by this symbol must be repeated on the opposite side of the vehicle. [. . . ] Drain plug (2) driving torque: 27 Nm (2. 7 kgm). Pour about 820 cm> of transmission oil through the filling opening (4), see p. 32 (STARTING) and let it idle for about one minute, in order to ensure the filling up of the transmission oil circuit. Check the oil level and top up if necessary, see p. 44 (CHECKING THE TRANSMISSION OIL LEVEL AND TOPPING UP). WARNING Tighten the filling plug and the drain plug thoroughly and make sure that there are no oil leaks. Periodically check that there are no leaks in correspondence with the oil pan cover seal. Do not use the vehicle with insufficient lubrication or with contaminated or unsuitable lubricants, since this would accelerate the wear of the moving parts and may also cause irreparable failures. NOTE Position the vehicle on firm and flat ground. Stop the engine and let it cool down for at least ten minutes, in order to allow the oil to flow back to the oil pan and to cool down. Keep the vehicle in vertical position, with the two wheels resting on the ground. Put a container (1) with at least 900 cm> capacity in correspondence with the drain plug (2). Unscrew and remove the filling plug (3). Drain the oil and let it drip into the container (1) for a few minutes. Remove the metal residues from the drain plug (2) magnet. Check and if necessary replace the sealing washer of the drain plug (2). use and maintenance RS 50 Tuono 45 4 FRONT WHEEL WARNING The disassembly and reassembly of the front wheel may be difficult for unskilled operators. If necessary, contact an aprilia Official Dealer. If you want to perform these operations personally, keep to th e following instructions. While disassembling and reassembling the wheel, be careful not to damage the brake pipes, the discs and the pads. DISASSEMBLY Position the vehicle on the appropriate rear support stand, see p. REAR SUPPORT STAND Position the vehicle on the appropriate front support stand, see p. FRONT SUPPORT STAND Withdraw the brake caliper (2) from the disc, leaving it attached to the pipe (3). CAUTION Never pull the front brake lever after removing the brake caliper, otherwise the caliper pistons may go out of their seats, thus causing the outflow of the brake fluid. In this case consult your aprilia Official Dealer, who will carry out the proper maintenance operation. WARNING Make sure that the vehicle is stable. NOTE To remove the front wheel it is necessary to use the appropriate front and rear support stands . Have someone keep the handlebar steady in running position, so that the steering is locked. Brake caliper screw (1) driving torque: 22 Nm (2. 2 kgm). Unscrew and remove the two screws (1) that fasten the front brake caliper (2). Put a support (4) under the tyre, in such a way as to keep the wheel in its position after loosening it. Lock the wheel pin (5) by means of a spanner. [. . . ] 00965-4828073 - Email: zed@zedmotorz. com RSA MOTOVELO S. A. MEX APRILIA DE MEXICO, SA. LTD. RP ULTRA BIKERS NETWORK INC. SGP CYCLENET PTE TLD HK AH LAM MOTORCYCLE CO. LTD. RC PERFECT MOTORS COMPANY LIMITED KWT ZED MOTORZ - Div. Of AL-RADWAN INTERNATIONAL GROUP RL ACCESS INTERNATIONAL FOR TRADING SARL. [. . . ]