User manual ZIBRO SRE 152 TC

[. . . ] SRE 152 TC 3 2 6 5 4 > 1 MANUEL D'UTILISATION GEBRAUCHSANWEISUNG BRUGSANVISNING INSTRUCCIONES DE USO OPERATING MANUAL ISTRUZIONI D'USO GEBRUIKSAANWIJZING 2 12 22 32 42 52 62 Dear Sir, Madam, Congratulations with your purchase of a portable domestic heater. You have purchased a quality product, which will serve you for many years to come. This, of course, provided you use the heater correctly. Please read these Directions for Use first, to ensure maximum lifetime for your heater. [. . . ] When the heater has been unplugged (or after a power failure), the temperature will reset to the factory setting of 20C. F USING THE TIMER The timer allows you to switch on the heater automatically at a preset time. In order to switch on the timer, the correct time must have been set (refer to Section C) and the heater should be off. Follow the procedure below: 1 Press the button and then the TIMER key will start blinking. immediately after that. The TIMER light and the 4-digit 2 Use the adjustment keys to set the time at which the heater must ignite. Use the key on the left (Nhour) to set the hours and the key on the right (Mmin. ) to set the minutes (interval of 5 minutes). 3 After approximately 10 seconds the 4-digit will show CLOCK again and the TIMER indicator light will light up, indicating that the timer function has been activated (Fig. 4 G: The TIMER indicator light indicates that the timer function has been switched on. The timer will ensure that the room will have been heated to approximately the required temperature at the set time. G H When you want to switch off the heater and ignite it again with the timer, all you have to do is press the TIMER key (refer to Section G). Press the button once to clear the timer setting. SWITCHING OFF THE HEATER There are two ways to switch off the heater. The information display will show the CLOCK signal. Within approximately one minute the flame will have extinguished. 2 Press the TIMER key , when you want to switch off the heater and ignite it again with the timer the next time. This not only switches off the heater, but it also activates the timer function. You can change the required time with the adjustment keys (refer to Section F). THE INFORMATION DISPLAY The information display not only serves as an indicator of the (set) time and temperature (sections C, E, and F), it also indicates any malfunctioning of the heater. The code on the information display tells you what is the matter: In case of any malfunctioning the information display will tell you what is the matter. CODE INFORMATION Temperature within the heater too high. Faulty thermostat. WHAT TO DO Cool-down and re-ignite. Contact your dealer. e- 0 f- 0 e- 1 4 47 feeee- 1 2 5 6 7 Faulty burner thermistor. The heater has been in operation continuously for a period of 48 hours and has turned itself off automatically. Contact your dealer. Contact your dealer. e- 8 e- 9 Switch the heater back on. Ventilate better. -- : -- + -- : -- + Out of fuel. Too little ventilation. Always contact your dealer for any malfunctioning not listed above. AUTOMATIC DEACTIVATION This heater is fitted with a safety system that ensures that it switches off automatically after 48 hours continuous operation. The following will then appear in the display: the button . If desired, you can switch the heater on again by pressing (see section D). AUTOMATIC CLEANING MODE When the heater has been burning continuously for two hours at its highest setting, the burner will automatically start an autoclean procedure. The display will show the autocleaningcode cl:05 running back to cl:01. [. . . ] Do not refill nor service the heater when it is burning or still hot. Position the front of the heater at a distance of minimum 1. 5 metres from walls, curtains, and furniture. Do not use the heater in dusty rooms or places with strong draughts. In either situation you will not have optimum burning. [. . . ]