User manual ZIBRO SRE 170 TC

[. . . ] SRE 170 TC 3 2 6 5 4 > 1 : MANUEL D'UTILISATION GEBRAUCHSANWEISUNG BRUGSANVISNING INSTRUCCIONES DE USO OPERATING MANUAL ISTRUZIONI D'USO GEBRUIKSAANWIJZING INSTRUKCJI OBSLUGI 2 12 22 32 42 52 62 72 Dear Sir, Madam, Congratulations with your purchase of the Zibro, the number one brand among movable heaters. You have purchased a first-class quality product, which will serve you for many years to come. This, of course, provided you use the heater correctly. Please read these Directions for Use first, to ensure maximum lifetime for your Zibro . [. . . ] After approximately 10 4 46 seconds the light will stop blinking and the setting will be locked (Fig. The available temperature settings range from 6C minimum to 28C maximum. When the heater has been unplugged (or after a power failure), the temperature will reset to the factory setting of 20C. F USING THE TIMER The timer allows you to switch on the heater automatically at a preset time. In order to switch on the timer, the correct time must have been set (refer to Section C) and the heater should be off. Follow the procedure below: 1 Press the button and then the TIMER key immediately after that. The TIMER light and the information display will start blinking. 2 Use the adjustment keys Use the key on the left ( to set the time at which the heater must ignite. hour) to set the hours and the key on the right ( min. ) to set the minutes (interval of 5 minutes). 3 After approximately 10 seconds the information display will show CLOCK again and the TIMER indicator light will light up, indicating that the timer function has been activated (Fig. 4 The timer will ensure that the room will have been heated to approximately the required temperature at the set time. H: The TIMER indicator light indicates that the timer function has been switched on. G H When you want to switch off the heater and ignite it again with the timer, all you have to do is press the TIMER key (refer to Section G). Press the button once to clear the timer setting. If you would like more extensive timer possibilities, we advise you to procure the Zibro weektimer. This timer is easy to connect with your Zibro Heater, see . SWITCHING OFF THE HEATER There are two ways to switch off the heater. The information display will show the CLOCK signal. Within approximately one minute the flame will have extinguished. 2 Press the TIMER key , when you want to switch off the heater and ignite it again with the timer the next time. This not only switches off the heater, but it also activates the timer function. You can change the required time with the adjustment keys (refer to Section F). E- 0 THE INFORMATION DISPLAY The information display not only serves as an indicator of the (set) time and temperature (Sections C, E, and F), it also indicates any malfunctioning of the heater. The code on the information display tells you what is the matter: CODE INFORMATION Temperature within the heater too high. WHAT TO DO Cool-down and re-ignite. In case of any malfunctioning the information display will tell you what is the matter. e- 0 4 47 fefeeee- 0 1 1 2 5 6 7 Power interrupted. The heater has been in operation continuously for a period of 65 hours and has turned itself off automatically. Re-ignite the heater. Clean filter Contact your dealer. e- 8 e- 9 Switch the heater back on. Ventilate better. --blinking : -(& FUEL-light) Out of fuel. Too little ventilation. --blinking : -(& VENT-light) Always contact your Zibro dealer for any malfunctioning not listed above. 65 H AUTOMATIC DEACTIVATION This heater is fitted with a safety system that ensures that it switches off automatically after 65 hours continuous operation. The following will then appear in the display: the button . [. . . ] Should this happen, never try to move the heater, but always switch off the heater immediately. In case of emergency you may use a fire extinguisher, but only a type B extinguisher: a carbon dioxide or powder extinguisher. 10 TIPS FOR SAFE USE 1 2 3 4 Make sure that children are always aware of the presence of a burning heater. Do not move the heater when it is burning or still hot. Do not refill nor service the heater when it is burning or still hot. [. . . ]