User manual ZIBRO SRE 179E

[. . . ] SRE 179 E 3 2 6 5 FIN MANUEL D'UTILISATION GEBRAUCHSANWEISUNG BRUGSANVISNING INSTRUCCIONES DE USO KYTTOHJE OPERATING MANUAL ISTRUZIONI D'USO BRUKSANVISNING GEBRUIKSAANWIJZING BRUKSANVISNING 2 10 20 30 40 50 60 70 80 90 4 > u 1 = 3 PAGE PLIANTE FALTBLATT FOLDEUDSIDE HOJA DESPLEGABLE AUKI TAITETTU SIVU FOLD-OUT PAGE PIEGHEVOLE UTBRETTSIDE UITVOUWBLAD UTVIKNINGSSIDA 2 6 5 FIN 5 4 > u 1 = - EMC - LV Dear Sir, Madam, Congratulations with your purchase of the Zibro, the number one brand among movable heaters. You have purchased a first-class quality product, which will serve you for many years to come. This, of course, provided you use the heater correctly. Please read these Directions for Use first, to ensure maximum lifetime for your Zibro. [. . . ] 3 After approximately 10 seconds the information display will show CLOCK again and the TIMER indicator light will light up, indicating that the timer function has been activated (Fig. 4 The timer will ensure that the room will have been heated to approximately the required temperature at the set time. H: The TIMER indicator light indicates that the timer function has been switched on. G H In case of any malfunctioning the information display will tell you what is the matter. When you want to switch off the heater and ignite it again with the timer, all you have to do is press the TIMER key (refer to Section G). Press the button once to clear the timer setting. SWITCHING OFF THE HEATER There are two ways to switch off the heater. The information display will show the CLOCK signal. Within approximately one minute the flame will have extinguished. 2 Press the TIMER key , when you want to switch off the heater and ignite it again with the timer the next time. This not only switches off the heater, but it also activates the timer function. You can change the required time with the adjustment keys (refer to Section F). THE INFORMATION DISPLAY The information display not only serves as an indicator of the (set) time and temperature (Sections C, E, and F), it also indicates any malfunctioning of the heater. The code on the information display tells you what is the matter: CODE INFORMATION Temperature within the heater too high. Clean filter Contact your dealer. efefeeee- 0 0 1 1 2 5 6 7 e- 8 e- 9 4 55 -- : -- + -- : -- + e-11+ The heater has been in operation continuously for a period of 69 hours and has turned itself off automatically. Too little ventilation. hours Switch the heater back on. Ventilate better. Always contact your Zibro dealer for any malfunctioning not listed above. AUTOMATIC DEACTIVATION This heater is fitted with a safety system that ensures that it switches off automatically after 69 hours continuous operation. The following will then appear in the display: . If desired, you can switch the heater on again by pressing the button (see Section D). AUTOMATIC CLEANING MODE When the heater has been burning continuously for two hours at its highest setting, the burner will automatically start an autoclean procedure. The display will show the autocleaning code cl:05 running back to cl:01. The procedure takes 5 minutes, during which the heater will burn at its lowest setting, while the burner autocleans. By pushing this button, the remaining heating time will extend to 90 minutes. The heater will automatically switch back to its lowest position. In the display the number 90 will appear, which will decline to 10. At the arrival of 10, you will hear an alarm signal every two minutes, warning you to refill the removable tank. If you do not react, the heater will extinguish by itself. The heater will also sound a warning signal, when it switches off. [. . . ] Position the front of the heater at a distance of minimum 1. 5 metres from walls, curtains, and furniture. You will not have optimum burning in such rooms. Do not use the heater in the immediate surrounding of a bath, a shower or a swimmingpool. Switch off the heater, before you leave or go sleeping. [. . . ]