User manual ZIBRO SRE 25 E

[. . . ] SRE 25 E 3 2 6 5 FIN MANUEL D'UTILISATION GEBRAUCHSANWEISUNG BRUGSANVISNING INSTRUCCIONES DE USO KYTTOHJE OPERATING MANUAL ISTRUZIONI D'USO BRUKSANVISNING GEBRUIKSAANWIJZING BRUKSANVISNING 2 14 26 38 50 62 74 86 98 110 4 > u 1 = 3 PAGE PLIANTE FALTBLATT FOLDEUDSIDE HOJA DESPLEGABLE AUKI TAITETTU SIVU FOLD-OUT PAGE PIEGHEVOLE UTBRETTSIDE UITVOUWBLAD UTVIKNINGSSIDA 2 6 5 FIN 5 4 > u 1 = a - EMC a - LV Dear Sir, Madam, Congratulations with your purchase of a portable domestic heater. You have purchased a quality product, which will serve you for many years to come. This, of course, provided you use the heater correctly. Please read these Directions for Use first, to ensure maximum lifetime for your heater. [. . . ] Next, adjust the temperature using the key on the right (Mmin. ) to set the temperature to a 4 66 higher setting and the key on the left (Nhour) to lower the temperature. Press once to increase the value one step. After approximately 10 seconds the C mark and 4-digit will stop blinking and the setting will be locked (Fig. The available temperature settings range from 6C minimum to 28C maximum. When the heater has been unplugged (or after a power failure), the temperature will reset to the factory setting of 20C. F USING THE TIMER The timer allows you to switch on the heater automatically at a preset time. In order to switch on the timer, the correct time must have been set (refer to Section C) and the heater should be off. Follow the procedure below: 1 Press the button and then the TIMER key immediately after that. The TIMER lamp and the 4-digit will start blinking. to set the time at which the heater must ignite. 2 Use the adjustment keys Use the key on the left (Nhour) to set the hours and the key on the right (Mmin. ) to set the minutes (interval of 5 minutes). 3 After approximately 10 seconds the 4-digit will show CLOCK again and the TIMER lamp G: The TIMER indicator light indicates that the timer function has been switched on. will light up, indicating that the timer function has been activated (Fig. G). 4 The timer will ensure that the room will have been heated to approximately the required temperature at the set time. G When you want to switch off the heater and ignite it again with the timer, all you have to do is press the TIMER key (refer to Section G). Press the button once to clear the timer setting. SWITCHING OFF THE HEATER There are two ways to switch off the heater. 1 Press the button . The information display will show the CLOCK signal. Within approximately one minute the flame will have extinguished. 2 Press the TIMER key , when you want to switch off the heater and ignite it again with the timer the next time. This not only switches off the heater, but it also activates the timer function. You can change the required time with the adjustment keys (refer to Section F). 4 67 H THE INFORMATION DISPLAY The information display not only serves as an indicator of the (set) time and temperature (sections C, E, and F), it also indicates any malfunctioning of the heater. The code on the information display tells you what is the matter: CODE INFORMATION Temperature within the heater too high. The heater has been in operation continuously for a period of 48 hours and has turned itself off automatically. Contact your dealer. In case of any malfunctioning the information display will tell you what is the matter. efefeeee- 0 0 1 1 2 5 6 7 e- 8 e- 9 -- : --- : -- + e-11+ + Out of fuel. Too little ventilation. Always contact your dealer for any malfunctioning not listed above. AUTOMATIC DEACTIVATION This heater is fitted with a safety system that ensures that it switches off automatically after 48 hours continuous operation. The following will then appear in the display: the . If desired, you can switch the heater on again by pressing button (see section D). AUTOMATIC CLEANING MODE When the heater has been burning continuously for two hours at its highest setting, the burner will automatically start an autoclean procedure. The display will show the autocleaningcode cl 05 running back to cl 01. The procedure takes 5 minutes, during which the heater will burn at its lowest setting, while the burner autocleans. [. . . ] Do not use the heater in dusty rooms or places with strong draughts. In either situation you will not have optimum burning. Do not use the heater in the immediate surrounding of a bath, a shower or a swimmingpool. Switch off the heater, before you leave or go to sleep. [. . . ]