User manual ZONET KVM3002

[. . . ] Introduction Thank you for purchasing KVM switch. KVM switch can save your MONEY, TIME, SPACE, EQUIPMENT and POWER. Controlling multiple PCs from One Keyboard, Mouse and VGA Monitor. [. . . ] Buzzer sound for switching port confirmation. Hardware Installation Before installation, please make sure all of peripherals and computers have been turned off. Connect the Keyboard, VGA, Mouse cables to the computer ports of KVM switch 2. Connect the Keyboard, VGA monitor, and Mouse to console port of KVM switch 3. After Powering on computers and finishing the boot-up process, you can start to go KVM switch. Note: * Please don't switch the PC port (i. e. Don't press the push button of KVM switch or run hot key) during the computers are under boot-up process. * If power off the first PC with port 1 (PC1), then power on the second PC with port 2 (PC2), please select the PC2 port with the push button of KVM Switch at first. (Only for 2-PORT KVM Switch) Package Contents 2 PORT KVM 2 port KVM Switch User's manual 4 port KVM Switch User's manual 4 PORT KVM Technical Specifications Functions PC Port Console Port MAX PC Connections LED PC Port Connector (All Female Type) Console port connector (All Female Type) PC selection On Screen Display Control Scan Intervals Keyboard Emulation Mouse Emulation VGA Resolution Bandwidth Daisy Chain and Levels Housing Size Weight (g) Dimension (mm) 2 PORT KVM 2 1 2 2 PS/2 Keyboard mini-Din 6 pin PS/2 Mouse mini-Din 6 pin VGA HDDB 15pin PS/2 Keyboard mini-Din 6 pin PS/2 Mouse mini-Din 6 pin VGA HDDB 15pin Hot Key / Button No 8sec. PS2 PS2 1920X1440 200MHz NO Plastic Mini Desktop 140g 110(L) X 74(W) X 29(H) Plastic Desktop 300g 190(L) X 74(W) X 29(H) 4 PORT KVM 4 1 4 4 Product Details 2 PORT KVM <Diagram> 4 PORT KVM <Diagram> System Requirements Specifications Functions Console side 2 PORT KVM One VGA Monitor One PS/2 Keyboard One PS/2 Mouse Two HDB 15 pin male to male VGA cables Two PS/2 cable male to male for Keyboard Two PS/2 cable male to male for Mouse 4 PORT KVM One VGA Monitor One PS/2 Keyboard One PS/2 Mouse Four HDB 15 pin male to male VGA cables Four PS/2 cable male to male for Keyboard Four PS/2 cable male to male for Computer Side Usage The push Button: Pressing the button cyclically through all the ports. 2 PORT KVM 1 2 Normally, there is one LED is always lit (i. e. the console is connected to this PC port) for one PC port and the other PC port's LED is off, when you power on KVM switch. When you select one of two PCs and it is shut down, the selected port LED flashed. 4 PORT KVM 1 2 3 4 When you select one of four PCs and it is powered on, the selected port LED is lit. When you select one of four PCs and it is shut down or disconnected a PC, the selected port LED flashed. Keyboard Hot Key Commands: You can also conveniently command KVM to switch ports through simple key sequences. To send commands to KVM, The Scroll Lock or Num Lock key must be pressed twice within 2 seconds than key in the enter. Below are the different commands: 1. KVM3002/3004 + 1. KVM3004 + + Previous Channel + + Previous Channel + OR + + + + Next Channel + + Next Channel OR Select PC port directly Beeper On (Factory default Off) Select PC port directly Beeper On (Factory default Off) + + + + + + + + Troubleshooting Ensure that all cables are well seated. Label all of cables with the number for each respective computer to avoid confusion. KVM switch draws the power from keyboard port of computers. [. . . ] Make sure the mouse is a true PS/2 mouse. A combo mouse will work just as long as it is set for PS/2 mode with the correct adapter. Avoiding moving the mouse or pressing the mouse buttons when switching the port. ! [. . . ]