User manual ZONET ZEW2500P

[. . . ] Copyright Statement is the registered trademark of Zonet Technology Inc. All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Zonet Technology Inc. Without the permission of Zonet Technology Inc. , any individual or party is not allowed to copy, plagiarize, imitate or translate it into other languages. 802. 11g Wireless USB Adapter Table of Content Chapter 1. [. . . ] Fast Roaming at: Fast to roaming, setup by transmitting power Enable CCX(Cisco Compatible eXtensions): a. Enable Radio Measurement: channel measures every 0~2000 milliseconds 3. 1. 5 Statistics Statistics tab displays the detail counter information based on 802. 11 MIB counters. This page translates that MIB counters into a format easier for user to understand. 10 802. 11g Wireless USB Adapter 3. 1. 6 WMM WMM Enable: Enable Wi-Fi Multi-Media WMM - Power Save Enable: Enable WMM Power Save Direct Link Setup Enable: Enable DLS (Direct Link Setup). This function will greatly improve the data transfer rate between WMM-enabled wireless devices. MAC Address: Input the MAC address of another WMM-enabled wireless device you wish to establish a direct link. Timeout Value: must be between 0~65535 in integer. If the value is zero represents it always connects. Default value of Timeout Value is 60 seconds. Tear Down: If you want to remove a specific wireless device from DLS table, select the device and click this button to remove it. 11 802. 11g Wireless USB Adapter 3. 1. 7 WPS WPS tab supports the configuration setup using PIN configuration method or PBC configuration method. WPS(Wi-Fi Protected Setup) simplify the security setup and management of Wi-Fi networks. PIN: Enter the Pin code and click PIN to automatically connect ZEW2500P with wireless devices around. PBC: Click PBC to complete auto-check and connections between ZEW2500P and other wireless device. Rescan: Update information on surrounding wireless network. Connect: click to connect the WPS wireless network. Disconnect: to disconnect the connected wireless network. 12 802. 11g Wireless USB Adapter 3. 2 AP Mode ZEW2500P also can serve as an access point to transmit wireless signals and create wireless network, allowing other wireless clients to access the network. Right-click the tray icon and select Switch to AP Mode. 3. 2. 1 Configuration In soft AP configuration Utility page, you can make some basic configurations, such as wireless network name, mode, channel and authentication. 13 802. 11g Wireless USB Adapter Click Security Setting button to make different security configurations of wireless communication, and you can choose the authentication type or encryption type. Note: 1. The Hex characters include 0~9 numbers and a~f letters. ASCII characters include any numbers/letters and characters. 14 802. 11g Wireless USB Adapter 3. 2. 2 Access Control Choose Access Control tab to start MAC control. Access control includes Allow All and Reject All. After editing the MAC address access list, only the MAC in the Allow All list could access the Soft AP. 15 802. 11g Wireless USB Adapter 3. 2. 3 MAC Table MAC Table page shows the information of the wireless devices accessed to this soft AP. 3. 2. 4 Switch to Working Station mode In the Soft AP mode, right-click the icon in the system tray and choose Switch to Station Mode, then ZEW2500P is switching to working station mode with an interface of working station. 16 802. 11g Wireless USB Adapter 3. 3 Use Zero Configuration Windows XP and Vista has a built-in wireless network configuration utility "Windows Zero Configuration" (WZC). It is a built in service to configure your wireless clients from Windows 1. Start using WZC, right click the tray icon Configuration as Configuration utility. The windows wireless network connection will appear. Double click the wireless network icon on the system tray to check the wireless network, choose the network and click Connect to setup the association. 3. [. . . ] Please note that it might be necessary to set up one client to establish a BSS (Basic Service Set) and wait briefly before setting up other clients. This prevents several clients from trying to establish a BSS at the same time, which can result in multiple singular BSSs being established, rather than a single BSS with multiple clients associated to it. Check that the Network Connection for the wireless client is configured properly. If Security is enabled, make sure that the correct encryption keys are entered on both ZEW2500P and the access point. 24 802. 11g Wireless USB Adapter 4. [. . . ]