User manual ZONET ZSR1114WE

[. . . ] User's Manual Version: 1. 1 Wireless LAN Broadband Router Trademarks Copyright @2005 Contents are subject to change without notice. All trademarks belong to their respective proprietors. Copyright Statement THIS DOCUMENT CONTAINS OF PROPRIETARY TECHNICAL INFORMATION THAT IS THE PROPERTY OF THIS COMPANY. AND NO PART OF THIS DOCUMENTATION MAY BE REPRODUCED, STORED IN A RETRIEVAL SYSTEM OR TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRICAL OR MECHANICAL, BY PHOTOCOPYING, RECORDING, OR OTHERWISE, WITHOUT THE PRIOR WRITTEN CONSENT OF THIS COMPANY. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Click the Reset button to abort change and recover the previous configuration setting. 3. 3. 8 WDS Settings Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set these APs in the same channel and set MAC address of other AP that you want to communicate with in the table and then enable the WDS. Screen snapshot ­ WDS Setup 22 USER'S MANUAL OF WLAN BROADBAND ROUTER Version: 1. 0 Item Enable WDS Description Click the check box to enable wireless distribution system. Refer to 4. 21 What is Wireless Distribution System (WDS)?Fill in the MAC address of AP to register the wireless distribution system access capability. Fill in the comment tag for the registered AP. Click the Apply Changes button to register the AP to new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. Click button to configure wireless security like WEP(64bits), WEP(128bits), WPA(TKIP), WPA2(AES) or None MAC Address Comment Apply Changes Reset Set Security Show Statistics Delete Selected Delete All Reset It shows the TX, RX packets, rate statistics Click to delete the selected clients that will be removed from the wireless distribution system. Click to delete all the registered APs from the wireless distribution system allowed list. Click the Reset button to abort change and recover the previous configuration setting. I WDS Security Setup Requirement: Set [Wireless]->[Basic Settings]->[Mode]->AP+WDS This page is used to configure the wireless security between APs. Refer to 3. 3. 6 Wireless Security Setup. 23 USER'S MANUAL OF WLAN BROADBAND ROUTER Version: 1. 0 Screen snapshot ­ WDS Security Setup II WDS AP Table This page is used to show WDS statistics Screen snapshot ­ WDS AP Table Item MAC Address Tx Packets Tx Errors Rx Packets Description It shows the MAC Address within WDS. It shows the statistic count of sent packets on the wireless LAN interface. It shows the statistic count of error sent packets on the Wireless LAN interface. It shows the statistic count of received packets on the wireless LAN interface. 24 USER'S MANUAL OF WLAN BROADBAND ROUTER Version: 1. 0 Tx Rare (Mbps) Refresh Close It shows the wireless link rate within WDS. Click to refresh the statistic counters on the screen. Click to close the current window. 3. 3. 9 Site Survey This page is used to view or configure other APs near yours. Screen snapshot ­ Wireless Site Survey Item SSID BSSID Channel Type Encrypt Signal Select Refresh Connect Description It shows the SSID of AP. It show the current channel of AP occupied. Click to select AP or client you'd like to connect. Click the Refresh button to re-scan site survey on the screen. Click the Connect button to establish connection. 3. 3. 10 LAN Interface Setup This page is used to configure the parameters for local area network that connects to the LAN ports of your WLAN Broadband Router. Here you may 25 USER'S MANUAL OF WLAN BROADBAND ROUTER Version: 1. 0 change the setting for IP address, subnet mask, DHCP, etc. Screen snapshot ­ LAN Interface Setup Item IP Address Subnet Mask Default Gateway DHCP Server DHCP Client Range Description Fill in the IP address of LAN interfaces of this WLAN Broadband Router. Fill in the subnet mask of LAN interfaces of this WLAN Broadband Router. [. . . ] For enterprise networks, an 54 USER'S MANUAL OF WLAN BROADBAND ROUTER Version: 1. 0 authentication server, typically one that supports RADIUS and the selected EAP authentication protocol, will be added to the network. 4. 16 What is WPA2? It is the second generation of WPA. WPA2 is based on the final IEEE 802. 11i amendment to the 802. 11 standard. 4. 17 What is 802. 1x Authentication? 802. 1x is a framework for authenticated MAC-level access control, defines Extensible Authentication Protocol (EAP) over LANs (WAPOL). The standard encapsulates and leverages much of EAP, which was defined for dial-up authentication with Point-to-Point Protocol in RFC 2284. Beyond encapsulating EAP packets, the 802. 1x standard also defines EAPOL messages that convey the shared key information critical for wireless security. 4. 18 What is Temporal Key Integrity Protocol (TKIP)? The Temporal Key Integrity Protocol, pronounced tee-kip, is part of the IEEE 802. 11i encryption standard for wireless LANs. [. . . ]