User manual ZOOM 2020

[. . . ] Thank you for selecting the advanced guitar effects processor ZOOM Player 2020 (hereafter called "2020"). The 2020 is a sophisticated multi-effect device with the following features and functions: · A total of 19 built-in individual effects, which can be combined in patches of up to six effects of five types. 20 preset patches and a user memory for 20 additional patches offer extraordinary flexibility. · Integrated foot pedals and informative control panel show settings at a glance and allow easy operation like a compact effector. [. . . ] When the effect type is changed, the setting of parameters 1 - 5 also changes. Therefore it is best to first select the effect type and then work on the other parameters when creating an effect from scratch. (2) Parameter value The value of the parameter currently selected for editing is shown on the display. (3) Parameter type The type of the parameter currently selected for editing is indicated by the flashing module cursor LED and parameter cursor LED. COMP+ DIST EFFECT 1 CLN I 3 OD I 5 DST I 2 CLN II 4 OD II 6 DST II PARM1 PARM2 PARM3 PARM4 PARM5 ZNR [0-15] COMP [0-3] EDGE [0, 1] 3 ­ 6 GAIN [1-8] · Use the VALUE +/- keys to change the parameter value. The value of the currently selected parameter is changed. To change values continuously, hold down the key. To change values quickly, press the other key as well. EQ 1 EQ HIGH [­7- +7] MID [­7-+7] MIDf [1-16] LOW [­7-+7] LEVEL [1-8] MODULATION 2 WAH SENS [0-10] FREQ [1-64] DELAY 1 MONO 2 PPD [0-10](x100mS) DELAY TIME [0-99](mS) 6 STR [0, 1] REVERB 1 REV 2 E/R TIME [1-10] TONE [­7-+7] MIX [0-10] PATCH LEVEL [0-31] 1 PIT PIT [­12-+12] FINE [­10-+10] BAL [0-10] 2 PHA 3 FLG 4 TRM 5 STEP 6 CHO DEPTH [0-10] RATE [1-50] 2 ­ 5 PERK [0-10] 3 DELAY TIME [0-90](x100mS) FEEDBACK [0-10] FEEDBACK [0-10] MIX [0-10] 1 COMP+DIST 2 EQ 3 MODULATION 4 DELAY B REVERB 11 HINT For details on the parameters of each effect module, please refer to "Effect Types and Parameters" on page 13. Storing a Patch If an edited patch (or a patch whose patch level setting was changed in the Play mode) is not stored, the change will be lost when another patch is selected. To preserve a setting, store the patch as described below. · Press the STORE key in the Play mode or Edit mode. This activates the store mode, and you can now choose the bank number and patch number in which you want to store the patch. group, parameters other NOTE For patches from the preset be stored. Therefore, than the patch level cannot even if a patch was chosen from the preset group, the store destination will automatically become "U" (user group) if a parameter other than the patch level was changed. If only the patch level was changed, the store destination can also be "P" (preset group). · Change other parameters in the same way. changes NOTE Parameter setting return to made in this way are only temporary. If you the Play mode or select a different patch without storing the new settings first, the settings will be lost. For details on how to store a patch, please refer to next section. Turning Effect Modules On and Off In the Edit mode, each effect can be turned on and off independently from others. · Pressing a pedal corresponding to an effect module that is currently on (pedal LED and effect module cursor LED are lit) turns the effect module off. Press the pedal again to turn the effect back on. · Use the BANK pedal and pedals 1 - 4 to specify the bank number and patch number. If no input is made, the patch will be stored in the original bank number and patch number. HINT The effect module on/off setting can also be stored as part of a patch. NOTE When a patch is stored, the patch that was previously stored in that number will be overwritten (erased). Take care not to erase a patch that you want to keep. When wishing to restore the factory preset patches, please refer to the explanation on page 18. Compare During editing, it is possible to temporarily return to the setting that was active before starting the editing process. This is called the "compare" function. · In the Edit mode, press the GROUP key. The previous value of the parameter where the cursor is currently located and the indication "CP" appear alternately on the display. The patch is stored, and the 2020 reverts to the Play mode. If the STORE key has not yet been pressed for the cancel the store process and return to the immediately preceding mode. NOTE second time, you can use the EDIT/CANCEL key to HINT When connecting the FP01 to a CONTROL IN jack, use the EXP. [. . . ] · Turn off the 2020 (with the amplifier volume set to minimum), and turn the unit back on while keeping the EDIT/CANCEL key depressed. The indication "FC" flashes on the display. This shows that the unit is ready for recalling individual patches from the internal ROM. Restoring All Factory Preset Patches (Initialize) This special function returns all patches in the preset group and the user group to the factory preset condition. Use this function with care, because all patches you have stored in the user group will be lost. [. . . ]