User manual ZOOM 510 DRIVER

[. . . ] Operation Manual Thank you for selecting the ZOOM 510 (hereafter simply called the "510"). Please take the time to read this manual carefully so you can get the most out of your 510 and ensure optimum performance and reliability. Retain this manual for future reference. ZOOM CORPORATION NOAH Bldg. , 2-10-2, Miyanishi-cho, Fuchu-shi, Tokyo 183, Japan PHONE: 0423-69-7116 FAX: 0423-69-7115 Printed in Japan 510-5000 1 Major Features · Dedicated distortion unit with two on-board distortion modules (PRE DRIVE and MAIN DRIVE). [. . . ] To activate this function, hold the EDIT key down for at least 1 second in Play mode. To turn the function off, again hold the EDIT key down for at least 1 second. Banks can be switched using the VALUE +/- keys. Bank Hold ON Keeping the EDIT key depressed for at least 1 second activates Bank Hold. To cancel Bank Hold, press the EDIT key again for 1 second. A1 Bank switching Banks A, b, C, d, E, F can be switched. PATCH DOWN PATCH UP Patch switching 4 patches within bank can be switched. Bank/patch switching when Bank Hold is on A1 BANK F BANK E BANK d BANK C BANK b BANK A PATCH 1 PATCH 2 PATCH 3 PATCH 4 PATCH 1 PATCH 2 PATCH 3 PATCH 4 PATCH 1 PATCH 2 PATCH 3 PATCH 4 PATCH 1 PATCH 2 PATCH 3 PATCH 4 PATCH 1 PATCH 2 PATCH 3 PATCH 4 PATCH 1 PATCH 2 PATCH 3 PATCH 4 A. 1 BANK HOLD ON A. 1 BANK HOLD OFF A1 BA NK 10 Patch Switching (Application: Direct Load OFF) In the default condition, the 510 is set up in such a way that pressing a patch pedal immediately switches the patch and alters the output sound. This switching principle is most convenient when the desired patches are adjacent or close to each other. However, when wanting to switch to a patch that is further away, it may be desirable not to activate the sound of the other patches in between. When this is desired, turn the Direct Load function off as follows. When Direct Load has been turned off, switching banks and patches has no effect until the user confirms the selection. DIRECT LOAD OFF Keeping STORE key depressed for 1 second turns Direct Load off. The same procedure serves to turn it on. For example, when going from patch 1 to patch 4 with Direct Load active, patches 2 and 3 will briefly be heard when the patch UP pedal is pressed three times. When Direct Load is off, pressing the patch UP pedal will change the number on the display (the number flashes), but until the user confirms the choice, the sound remains that of patch 1. To turn Direct Load on or off, keep the STORE key depressed for at least 1 second. To confirm a choice after selecting a patch with Direct Load off, press both patch pedals simultaneously. Example: Switching from patch 1 to patch 4 A1 A2 A3 A4 A4 BA NK DO WN PATCH DOWN UP A1 Bank switching Banks A, b, C, d, E, F can be switched. PATCH UP Patch switching Patches can be switched. Confirming a patch When display indication flashes, pressing both patch pedals together confirms the patch and switches the output sound. A4 Press both pedals together Patch switching completed Confirm 11 Editing Patches The 510 comes with 24 predefined patches. However, the 510 offers many more possibilities for combining effects in innovative ways. To discover these possibilities, we recommend that you try changing the parameters (elements that make up patches) to create your own patches. This operation is called editing, and is done in the Edit mode. To switch from normal Play mode to Edit mode, press the EDIT key briefly (for less than 1 second). * Note that if the EDIT key is held down for 1 second or longer, the Bank Hold mode will be activated. A1 (1) While still in Play mode, select (2) Press the EDIT key to the patch you wish to edit. activate the Edit mode. Immediately after entering Edit mode from Play mode, the topmost parameter cursor indicator (PRE DRIVE) flashes, and the setting of this parameter is shown on the display. The flashing parameter cursor always indicates which parameter is selected for editing. In Edit mode, the EDIT key or the PATCH UP/DOWN pedals serve to select the parameter. Each push of the EDIT key moves the blinking parameter cursor indicator one step down. The PATCH UP/DOWN pedals move the blinking parameter cursor indicator up or down. When the EDIT key is pressed while the lowest indicator (Parameter 8: LEVEL) is flashing, the TUNER indicator (Parameter 9: SERIAL/PARA) starts flashing. [. . . ] Connect the battery cable to the new battery, taking care to observe correct polarity (+/-). Then insert the battery into the battery compartment. Close the battery compartment cover, taking care not to pinch the cable. (Make sure that the cover is properly locked. ) Cover 6LR61 9 V (alkaline) battery Cable 15 Returning Patches to Factory Settings The 510 comes with 24 predefined patches that have been programmed at the factory. [. . . ]