User manual ZOOM FIRE36

[. . . ] FIRE36E. fm 1 ページ ２００４年６月２５日　金曜日　午前１１時１２分 Operation Manual Introduction T h a n k y o u f o r s e l e c t i n g t h e Z O O M M O D E L I N G G U I TA R AMPLIFIER FIRE-36 (simply called the "FIRE-36" in this manual). Please take the time to read this manual carefully so as to get the most out of this product and to ensure optimum performance and reliability. Please keep this manual in a convenient place for future reference. Contents USAGE AND SAFETY PRECAUTIONS . 15 Switching the mode with the foot switch . [. . . ] (For information on factory default patch contents, see page 17. ) Patch bank U: User bank; A, b: preset banks 4 Patch number When you press the [PROGRAM/BANK] key, the patch number stays the same and only the bank is toggled: U1 → A1 → b1 → U1. 3. Operate the controls in the input/preamp section and the effect section as required, to adjust the distortion, tone, volume, effect type and intensity, etc. It is also possible to modify a patch after it was loaded. When a knob or key was operated, a dot appears at the bottom right of the display. This indicates that the contents of the patch have changed. (When you return to the original settings, the dot disappears. ) 4 H INT Lit You can store the contents of a changed user patch by pressing the [STORE] key. For information on the procedure, see the section "Storing a patch". N OTE If you have changed some settings and then select another patch, the settings of the previous patch will return to the stored condition. If you want to preserve your changes, store the user patch. ZOOM FIRE-36 13 FIRE36E. fm 14 ページ ２００４年６月２５日　金曜日　午前１１時１２分 Using the FIRE-36 ◆ Storing a patch N OTE When you store a patch, any patch currently stored under the same number will be overwritten (erased and replaced with the new settings). Take care not to accidentally erase a patch that you want to keep. 1. 2. Use the knobs and keys on the panel to establish the desired sound. Press the [STORE] key in the patch section. The indication "U" (for user bank) and the patch number (0 - 9) are shown on the display. In this condition, storing the settings as a user patch is possible. 0 3. Use the [Q]/[W] keys to select the desired user patch (U0 - U9). The preset patches (A0 - A9, b0 - b9) are read-only and cannot be selected as store targets. 1 4. To store the patch, press the [STORE] key once more. The store process is carried out, and the unit goes into program mode. To cancel the process and return to the condition of step 1, press the [EXIT] key instead of the [STORE] key. H INT By calling up an existing patch and then selecting another destination for the store process, copying a patch is possible. 14 ZOOM FIRE-36 FIRE36E. fm 15 ページ ２００４年６月２５日　金曜日　午前１１時１２分 Using the FIRE-36 Using the built-in tuner The FIRE-36 incorporates an auto-chromatic tuner which can be activated by pressing the [TUNER] key. 1. Press the [TUNER] key in the patch section. The LED of the key lights up and the internal tuner becomes active. If you want to tune while keeping the sound output on, press the [TUNER] key only briefly. (The display indication shows "tU". ) If you want to tune while the sound is muted, hold down the [TUNER] key somewhat longer. (Release the key when the display indication shows "Mt". ) T Mute Hold down MT 2. Play the open string you want to tune The left side of the display shows the note which is closest to the current pitch. The right side of the display shows how far the pitch is off. Adjust the pitch while observing the display. Pitch is sharp Correct pitch Pitch is flat A8 A8 The higher the rotation speed, the more the pitch is off. 3. To change the tuner reference pitch, press one of the [Q]/[W] keys. The current reference pitch is shown for two seconds. The default setting is "40" (center A = 440 Hz). 40 4. While the reference pitch is shown, you can use the [Q]/[W] keys to change the setting. The setting range is 35 - 45 (center A = 435 Hz - 445 Hz). ZOOM FIRE-36 15 FIRE36E. fm 16 ページ ２００４年６月２５日　金曜日　午前１１時１２分 Using the FIRE-36 42 N OTE When power is turned off and on again, the reference pitch is reset to "40" (center A = 440 Hz). 5. When tuning is complete, press the [TUNER] key to turn the tuner off. The tuner function is disabled. N OTE During use of the tuner, effects are turned off. Switching the mode with the foot switch Using the separately available foot switch, you can toggle between manual mode and program mode during play. 1. Turn off power to the FIRE-36 and connect the foot switch FS-01 (available separately) to the [FOOT SW] jack. N OTE Please do not connect or disconnect the foot switch while power is turned on. 2. Turn power to the FIRE-36 on. The FIRE-36 is in manual mode. -3. Display in manual mode Press the foot switch while you are playing your instrument. When you push the foot switch, the FIRE-36 switches to program mode, and the currently selected patch becomes active. If required, use the [PROGRAM/BANK] key and [Q]/[W] keys to switch the bank and patch number. A1 Program mode display 16 ZOOM FIRE-36 FIRE36E. fm 17 ページ ２００４年６月２５日　金曜日　午前１１時１２分 Using the FIRE-36 4. To return to manual mode, press the foot switch again, or press the [MANUAL] key. Returning the FIRE-36 to the factory default settings (all initialize) If required, you can return the settings of the user patches (U0 - U9) to the condition in which the unit was shipped. (This function is called "all initialize". ) N OTE When you carry out this function, any settings that you have stored in user patches will be lost. Proceed with care. 1. Hold down the [STORE] key while turning power to the unit on. The indication "AL" appears on the display. AL 2. To execute the all initialize function, press the [STORE] key once more. All user patches are returned to the factory default condition. If you wish to cancel the process, press the [EXIT] key instead of the [STORE] key. ZOOM FIRE-36 17 FIRE36E. fm 18 ページ ２００４年６月２５日　金曜日　午前１１時１２分 Drive Types and Effect Types Drive Types and Effect Types ■ DRIVE Selects the modeling material (amp) and distortion type (drive type). Drive type Display Variation VINTAGE Name FDR BLUES FDR CLEAN Description Classic bluesy sound of built-in type tube amp. Nostalgic British-style tube stack amp sound. [. . . ] Serial connection of slow attack and pitch shift. Higher setting values result in slower attack speed. (Pitch shift is fixed to one octave higher. ) SLOW-A→PITCH A9 This effect varies the pitch of the original sound. You can select one of nine preset pitch shift patterns (P1 - P9). P1 P2 P3 P4 PITCH Mixes the original sound and a sound component shifted one octave down. [. . . ]