User manual ZOOM G7

[. . . ] If users ignore this symbol and handle the device the wrong way, bodily injury and damage to the equipment could result. Warning Caution Contents SAFETY PRECAUTIONS Usage Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Terms Used in This Manual . . . . . . . . . . . . . . . . . . . 5 Controls and Functions . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The operating environment conditions for this type of use are as follows. Compatible operating system The USB port of the G7. 1ut only serves for sending and receiving audio data. For MIDI messages, use the MIDI IN/OUT connectors. USB+DIRECT To use the G7. 1ut as an audio interface for the computer, connect the USB port of the G7. 1ut to a USB port on the computer. The G7. 1ut will be recognized as an audio interface. In this condition, the sound of a guitar connected to the INPUT jack of the G7. 1ut can be processed with the effects of the G7. 1ut and then be recorded on the audio tracks of a DAW (Digital Audio Workstation) software application on the computer (see Figure 1 below). When performing playback with the DAW application, the playback sound from the audio The signal after effect processing appears at the OUTPUT jack also when USB connection is used. USB Only · Windows XP · Mac OS X (10. 2 and later) Quantization The signal after effect processing at the OUTPUT jack is muted when USB connection is used. 16-bit Muting the direct output when using a USB connection When the G7. 1ut is connected to a computer and used as an audio interface, the signal appearing at the OUTPUT jack after effect processing may be muted if you want to monitor the sound from the DAW software only. HINT 4. When the setting is complete, press the [EXIT] key. The indication "Store. . . ?" appears on the display, to allow you to store the changes. Fig. 1: Signal flow during recording DAW software USB [USB] Store. . . ?Y[STORE] N[EXIT] 5. Press the [STORE/SWAP] key to save the changes. [INPUT] [OUTPUT] G7. 1ut Effects Fig. 2: Signal flow during playback (1) DAW software USB [USB] [INPUT] [OUTPUT] G7. 1ut Effects The following procedure is only valid when the G7. 1ut is connected to a computer via USB. 1. Fig. 3: Signal flow during playback (2) In play mode, press the [AMP SELECT/SYSTEM] key. For details, see the next page. LCD 2/26 ¡Contrast:1 Contrast:1 The live performance algorithm is selected for 50 ZOOM G7. 1ut ZOOM G7. 1ut 51 Linking Effects STACK R Linking Effects 3. Using the Amp Select Function The G7. 1ut incorporates an Amp Select function that optimizes the frequency response to match a the type of amplifier in use. When starting to use the G7. 1ut or when changing the guitar amp, you should choose a suitable Amp Select setting as described below. This setting is suitable when using the POWER INPUT on the rear panel of a Marshall stack amp. Turn parameter knob 1 to select "Befr" (before pre-amp section) or "Aftr" (after pre-amp section). 2. Turn parameter knob 2 to select "Pre" (before MOD/EFX2 module) or "Post" (after DELAY module). 3. 4. When the setting is complete, press the [EXIT] key. The indication "Store. . . ?" appears on the display, to allow you to store the changes. Press the [STORE/SWAP] key to save the changes. In the above condition (while "Store. . . ?" is shown), only the [STORE/SWAP], [EXIT], and [PAGE] keysp are active. By pressing the [EXIT] key, you can abort the changes and return to play mode without saving. When the setting is complete, press the [EXIT] key. To enable the changed setting, be sure to store the patch ( p. 27). 3. When the setting is complete, press the [EXIT] key. To enable the changed setting, be sure to store the patch ( p. 27). 4. Changing the insert position of the pre-amp section NOTE · When the "Pre" setting is selected as pre-amp section insert position, the signal after the MOD/ EFX2 module is processed entirely in stereo. When you select "Post", the signal is processed in the pre-amp section in mono. [. . . ] Set the level as high as possible without causing the meter to reach the end of the scale. To adjust the level, do not use the fader of Cubase LE 4. Instead change the recording level and gain settings at this unit. Go to beginning of project Play button 2. Use the button in the transport panel to move to the beginning of the project. 3. [. . . ]