User manual ZOOM G9.2TT

[. . . ] Operation Manual © ZOOM Corporation Reproduction of this manual, in whole or in part, by any means, is prohibited. SAFETY PRECAUTIONS Usage Precautions SAFETY PRECAUTIONS In this manual, symbols are used to highlight warnings and cautions for you to read so that accidents can be prevented. The meanings of these symbols are as follows: This symbol indicates explanations about extremely dangerous matters. If users ignore this Warning symbol and handle the device the wrong way, serious injury or death could result. This symbol indicates explanations about dangerous matters. [. . . ] MicType Dyna, Cond MicPosi 0­2 Depth 0­2 Z Clean Zoom original straight clean sound. The above 43 effect types have the same parameters. GAIN LEVEL Gain 0 ­ 100 Adjusts the preamp gain (distortion depth). PARM1 Level 1 ­ 100 Adjusts the signal level after passing the module. PARM2 Selects the microphone type. "Dyna" simulates the frequency response of a dynamic mic and "Cond" that of a condenser mic. Lets you select different characteristics according to the mic position. 0: Mic pointed at speaker Effect Depth 0 also includes center some Cabinet sound. 1: Mic pointed halfway between speaker edge and center 2: Mic pointed at speaker edge Tone Pre, Post Selects the connection position of the pre-amp Adjusts the tonal quality of the section. "Pre" (before MOD/EFX2 module) or "Post" (after DELAY module). 0 ­ 30 Chain MOD/EFX2 module This module comprises modulation effects such as chorus and flanger, delay effects, and pitch shifter effects. Chorus This effect mixes a variable pitch-shifted component to the original signal, resulting in full-bodied resonating sound. PARM1 PARM2 PARM3 PARM4 Aco. Sim This effect makes an electric guitar sound like an acoustic guitar. GAIN LEVEL Depth 0 ­ 100 Rate 1 ­ 50 Adjusts the effect depth. Adjusts the modulation rate. Mix 0 ­ 100 Adjusts the level of the effect Adjusts the tonal quality of the sound mixed to the original sound. sound. 0 ­ 10 Tone Top 0 ­ 10 Adjusts the characteristic strings sound of an acoustic guitar. PARM1 Level 1 ­ 100 ST-Chorus This is a clear sounding stereo chorus. PARM1 PARM2 PARM3 PARM4 Adjusts the signal level after passing the module. PARM2 Depth 0 ­ 100 Rate 1 ­ 50 Body Pre, Post Selects the connection position of the pre-amp Adjusts the characteristic body section. Available settings are sound of an acoustic guitar. "Pre" (before MOD/EFX2 module) or "Post" (after DELAY module). 0 ­ 10 Chain Adjusts the effect depth. Adjusts the modulation rate. Mix 0 ­ 100 Adjusts the level of the effect Adjusts the tonal quality of the sound mixed to the original sound. sound. 0 ­ 10 Tone 66 ZOOM G9. 2tt ZOOM G9. 2tt 67 Effect Types and Parameters Ensemble This is a chorus ensemble with three-dimensional movement. PARM1 PARM2 PARM3 PARM4 Effect Types and Parameters Vibe This is an effect with automatic vibrato. PARM1 PARM2 PARM3 PARM4 Depth 0 ­ 100 Rate 1 ­ 50 Adjusts the effect depth. Adjusts the modulation rate. Mix 0 ­ 100 Adjusts the level of the effect Adjusts the tonal quality of the sound mixed to the original sound. sound. 0 ­ 10 Tone Depth 0 ­ 100 Rate 0 ­ 50 Adjusts the effect depth. Adjusts the modulation rate. 0 ­ 10 0 ­ 100 Adjusts the balance between Adjusts the tonal quality of the original sound and effect sound. sound. Tone Balance ModDelay This is a delay that allows use of modulation. PARM1 PARM2 PARM3 PARM4 Step Special effect that changes the sound in a staircase pattern. PARM1 PARM2 PARM3 PARM4 Time 1­ 2000 mS FeedBack 0 ­ 100 Rate 1 ­ 50 Mix 0 ­ 100 Depth 0 ­ 100 Rate 0 ­ 50 Resonance Adjusts the resonance intensity. 0 ­ 10 Adjusts the modulation depth. Higher setting values Adjusts the modulation rate. result in a higher number of delay sound repetitions. Adjusts the level of the effect sound mixed to the original sound. 0 ­ 10 Adjusts the effect sound envelope. Shape Sets the delay time. Delay This is a delay with a maximum setting of 2000 ms. See TapeEcho (next effect) for effect parameters. Flanger This effect produces a resonating and strongly undulating sound. PARM1 PARM2 PARM3 PARM4 TapeEcho This effect simulates a tape echo. PARM1 PARM2 PARM3 PARM4 Depth 0 ­ 100 Rate 0 ­ 50 Adjusts the effect depth. Adjusts the modulation rate. Resonance -10 ­ -1, 0, Manual 0 ­ 100 1 ­ 10 Adjusts the resonance Adjusts the frequency range intensity. on which the effect operates. Time 1­ 2000 mS FeedBack 0 ­ 100 HiDamp 0 ­ 10 Mix 0 ­ 100 PitchShift This effect shifts the pitch up or down. PARM1 PARM2 PARM3 PARM4 Sets the delay time. Adjusts the amount of feedback. Higher setting values result in a higher number of delay sound repetitions. Adjusts the treble attenuation of the delay sound. Lower setting values result in softer delay sound. Adjusts the level of the effect sound mixed to the original sound. Shift -12 ­ -1, 0, Tone 1 ­ 12, 24 DynamicDelay 0 ­ 10 Fine -25 ­ 25 Balance 0 ­ 100 This is a dynamic delay where the effect volume varies according to the input signal level. PARM1 PARM2 PARM3 PARM4 Sets the pitch shift amount in semitones. Allows fine adjustment of Adjusts the tonal quality of the pitch shift amount in Cent (1/ sound. 100 semitone) steps. Adjusts the balance between original sound and effect sound. Time PedalPitch This effect allows using a pedal to shift the pitch in real time. PARM1 PARM2 PARM3 PARM4 1­ 2000 mS Amount 0 ­ 100 FeedBack 0 ­ 100 Sense -10 ­ -1, 1 ­ 10 Color 1­8 Mode Up, Down Tone Selects the type of pitch change caused by the pedal (see Table 1). [Table 1] Color Mode Sets the direction of the pitch change to Up or Down. PdlPosi 0 ­ 100 Sets the pitch shift amount. [. . . ] Click the Play button in the transport panel to start playback. NOTE · While the monitoring button is enabled, the direct signal input to this unit and the signal routed to the computer and then returned to this unit will be output simultaneously from this unit, causing a flanger-like effect in the sound. To accurately monitor the sound also while adjusting the recording level, temporarily set the output device port for the VST connection (step 6) to "Not Connected". · The level meter as in the above illustration shows the signal level after processing in this unit. When you pluck a guitar string the meter may register with a slight delay, but this is not a defect. HINT If no sound is heard when you click the Play button after recording, check the VST connection settings (step 6) once more. HINT The Inspector shows information about the currently selected track. [. . . ]