User manual ZOOM R24

[. . . ] · Parallel or serial connection of distortion modules allows the creation of variations that are difficult to achieve with conventional multi-effect devices, such as adding light distortion after strong distortion. The result is a wide variety of overdrive and distortion sounds. · Total of 16 effects (eight effect types per distortion module) can be combined . Besides distortion effects, PRE DRIVE also contains compressor, pedal wah, auto wah, octaver and other versatile effects. [. . . ] To cancel the Bypass/Tuner mode, just press one of the patch pedals. Press Release immediately Tuning function (only when the tuning function is ON) To cancel the Bypass mode, simply press one of the patch pedals. The unit then reverts to the previously selected patch. Tuner mode The 510 is initially set so that the auto-chromatic tuning function for the guitar activates automatically when the Bypass mode is invoked. In Bypass mode, pick an open string to be tuned. The closest note will be shown on the display. Input signal standby condition Regular tuning Do = C Do# = C# Regular tuning Re# = D# Regular tuning Fa# = F# 6th string 1st string Regular tuning La = A 3rd string 5th string Mi = E 4th string So = G So# = G# La# = A# Regular tuning Re = D Fa = F Si = B 2nd string When the tuning function is active, the parameter cursor LEDs serve as tuning meter, designed to enhance tuning precision during fine adjustments. Turning tuning function off If you do not want to activate the tuning function in Bypass Pitch is too high Correctly tuned Pitch is too low mode, press the STORE and EDIT keys simultaneously for more than one second in Play mode. The tuning function will be turned off, and this setting will be stored even when the power is turned off. When you turn the function off, the display will show "tunEr oFF" (tuning function off). To turn the tuning function on, press the same keys simultaneously again. The display will show "tunEr on" (tuning function on). NOTE: Please note that the tuning function may not operate properly if other effect modules between the guitar and the 510 are on. 9 Patch Switching (Application: Bank Hold ON) In the initial setting, the patch pedal switches all patches in order, regardless of the bank divisions. The bank hold function limits switching to the four patches within a bank. When this function is activated, the patch pedals switch in order between the patches in the current bank only. To activate this function, hold the EDIT key down for at least 1 second in Play mode. PATCH UP moves the blinking parameter cursor one step up and PATCH DOWN moves it one step down. * When the PATCH DOWN pedal is pressed while the TUNER indicator (Parameter 9: SERIAL/PARA) is flashing, the 510 stays in Edit mode and parameter 1 is selected. 7 Sr A1 There are a total of eight indicators, assigned to parameters 1 ­ 8 from top to bottom, plus the TUNER indicator which is assigned to parameter 9. The parameter functions are as follows. · Parameter 1:PRE DRIVE (PRE DRIVE effect type selection) · Parameter 2:GAIN (PRE DRIVE parameter setting) · Parameter 3:MAIN DRIVE (MAIN DRIVE effect type selection) · Parameter 4:GAIN (MAIN DRIVE parameter setting) · Parameter 5:HIGH (High-range equalizer) · Parameter 6:LOW (Low-range equalizer) · Parameter 7:ZNR/AMP (ZNR setting/amp simulator on, off) · Parameter 8:LEVEL (Patch level) · Parameter 9:SERIAL/PARA (Serial/parallel connection) (1) Use the EDIT key or patch (2) Use the VALUE +/- keys pedal to select the parameter to adjust the parameter. (3) While the TUNER indicator (Parameter 9) is flashing, press the EDIT key to return to Play mode. *Use the VALUE +/- keys to change the setting of the parameter. For details on parameters, please refer to section 12 "Effect Parameters". 12 Effect Parameters PARAMETER 1 PRE DRIVE Selects the effect type to be used in the PRE DRIVE module. 8 different effect types are available. (PRE DRIVE effect type) Increases or decreases the setting by 1 effect type. + ­ 1 BOOSTER 2 RHYTHM 3 LIGHT OD 4 DYNAMIC OD 5 COMP (Compressor) Conventional compressor effect. 6 AUTO WAH Auto wah with changing characteristics depending on picking intensity. 7 PEDAL WAH Pedal wah for use with optional expression pedal FP01. The center frequency that is being emphasized goes up and down, depending on the pedal action. 8 OCTAVE Natural sounding octaver creating a sound one octave lower. For use with single notes only. VALUE +/- keys + ­ Setting range 1 ­ Increases the setting by 1 effect type. Creates a Light distortion (Light overdrive) (Dynamic overdrive) clean sound suitable for Light overdrive Dynamic overdrive effect with prominent rhythm guitar. characteristics depending on picking intensity. PARAMETER 2 GAIN Sets the effect parameter value for PRE DRIVE. Which parameter is being adjusted depends on the effect type selected with parameter 1. (PRE DRIVE parameter setting) Increases or decreases the setting by 1. + ­ · GAIN: Adjusts the PRE DRIVE gain. Higher values result in higher PRE DRIVE gain and increased distortion. · SENS (Sensitivity) : Adjust the effect sensitivity. Higher values result in higher sensitivity. · FREQ (Frequency): Sets the center frequency that is active immediately after a patch is selected. [. . . ] Turn the 510 upside down and open the cover of the battery compartment. (Push the catch to unlock the cover, then lift it up. ) 2. Remove the battery from the compartment and disconnect the battery cable. (Grasp the terminal strip and do not pull at the cable. ) 3. [. . . ]