User manual ZOTAC ZBOX ID-84 PLUS

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - - - - REORIENT OR RELOCATE THE RECEIVING ANTENNA INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT OF THE RECEIVER CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN NOTE: Connecting this device to peripheral devices that do not comply with Class B requirements, or using an unshielded peripheral data cable, could also result in harmful interference to radio or television reception. The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. To ensure that the use of this product does not contribute to interference, it is necessary to use shielded I/O cables. Copyright This manual is copyrighted with all rights reserved. [. . . ] FP1-Pin Definition Pin 1 3 5 7 9 Signal HDD_LED+ HDD_LEDGND RESET NC Pin 2 4 6 8 10 Signal PW_LED+ PW_LED115XLM 1. 5V 120 240 121 120 240 GND KEY 121 Speaker Header -SPEAKER SPEAKER-Pin Definition PIN 1 2 3 4 Assignment VCC NC NC SPK1 FP1 1 SPEAKER 14 1. 5V PWR_SW Hardware Installation USB Headers-FP_U1/2 This motherboard contains four USB 2. 0 ports that are exposed on the rear panel of the chassis. The motherboard also contains two 10-pin internal headers onboard. Note: Secure the bracket to either the front or rear panel of your chassis (not all chassis are equipped with the front panel option). FP_U1/2-Pin Definition 1 3 5 7 9 VCC USBP0USBP0+ GND KEY 2 4 6 8 10 VCC USBP1USBP1+ GND NC 121 121 115XLM 1. 5V Front Panel Audio Header-FP_S The audio connector supports HD audio standard and provides two kinds of audio output choices: the Front Audio, the Rear Audio. The front Audio supports retasking function. FP_S-Pin Definition PIN 1 3 5 7 9 Assignment MIC2(L) MIC2(R) Front Audio(R) FAVDIO-JD Front Audio(L) PIN 2 4 6 8 10 Assignment GND NC Reserved Key(No pin) Reserved 1 FP_S 1 1 FP_U2 FP_U1 Note: In order to utilize the front audio header, your chassis must have front audio connector. Also please make sure the pin assignment on the cable is the same as the pin assignment on the mainboard header. To find out if the chassis you are buying supports a front audio connector, please contact your dealer. 1. 5V 120 240 120 240 PIN Assignment PIN Assignment 15 Intel H61-MATX series Motherboard CPUFAN 120 240 121 120 240 115XLM GND +12V Sense Control 1. 5V 1. 5V SATA1 SATA2 SATA3 SATA4 S-FAN1 GND +12V Sense Serial-ATA (SATA) Connectors (SATA1/2/3/4) The Serial ATA connector is used to connect the Serial ATA device to the motherboard. These connectors support the thin Serial ATA cables for primary storage devices. The current Serial ATA interface allows up to 300 MB/s data transfer rate. Fan Connectors There are two fan connectors on the motherboard, including system fan connectors: S-FAN1 and CPU fan connector: CPUFAN. 16 121 SATA-Pin Definition Pin 1 2 3 4 5 6 7 Signal GND TXP TXN GND RXN RXP GND Hardware Installation Expansion Slots The motherboard contains three expansion slots, including one PCI Express x16 slot and two PCI Express x1 slots. 120 240 121 120 240 115XLM 1. 5V PCIE1 PCIE2 PCIE3 PCI Express x16 Slot-PCIE1 There is one PCI Express x16 slot reserved for graphics or video cards. The PCIe x16 slot is complianting with PCIE 2. 0 specification. PCI Express x1 Slots-PCIE2/3 There is two PCI Express x1 slots that are designed to accommodate less bandwidth intensive cards, such as a modem or LAN card. Jumper Settings CMOS Clear Jumper-JP1 JP1 1 1 This section explains how to configure the motherboard’s hardware. Before using your computer, make sure all jumpers and DRAM modules are set correctly. If you disable this item, only one 64-bit line will be prefetched from the 128-bit section (including the required data). If you enable this item, two lines will be prefetched whether there is required data or not. Storage Configuration The items in this menu allow you to set or change the storage configurations. Press <enter>to display the configuration options: q SATA Controllers Use this item to enable or disable SATA controllers. q SATA Mode Selection Allows you to choose SATA mode, including [Disabled], [IDE Mode], and [AHCI Mode]. q SATA Test Mode Use this item to enable or disable SATA test mode. The items in this menu allow you to change the USB-related features. Press <enter> To display the configuration options: q Legacy USB Support Allows you to enable or disable support for USB devices on legacy operating systems. q EHCI Hand-Off Allows you to enable support for operating systems without an EHCI hand-off feature. q USB transfer time-out Allows you to set USB transfer time-out. q Device reset time-out Allows you to set device reset time-out. q Device power-up delay Allows you to set device power-up delay. USB Configuration 20 Configuring the BIOS F71808A Super IO Configuration The items in this menu allow you to configure F71808A Super IO Chipset. [. . . ] Select this item to set the user password. Configuring the BIOS To set an Administrator/User Password: 1. Select the item [Administrator/User Password] and press <Enter>. From the password box, type a password composed of at least six letters and/or numbers, then press <Enter>. Confirm the password when prompted: The message “Password Installed” appears after you successfully set your password. [. . . ]