User manual ZOTAC ZBOX ID-85 PLUS

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - - - - REORIENT OR RELOCATE THE RECEIVING ANTENNA INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT OF THE RECEIVER CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN NOTE: Connecting this device to peripheral devices that do not comply with Class B requirements, or using an unshielded peripheral data cable, could also result in harmful interference to radio or television reception. The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. To ensure that the use of this product does not contribute to interference, it is necessary to use shielded I/O cables. Copyright This manual is copyrighted with all rights reserved. [. . . ] It is fully compliant with PCIE 2. 0 specification. 20 1. 5V Hardware Installation Jumper Settings This section explains how to configure the motherboard’s hardware. Before using your computer, make sure all jumpers and DRAM modules are set correctly. Refer to this section whenever in doubt. CMOS Clear Jumper-JP1 JP1 1 1 Selection Normal* CMOS Clear Open * = Default setting. 1-2* 2-3 Close If you want to clear the system configuration, use the JP1 (Clear CMOS Jumper) or SW1 (Clear CMOS Button) to clear data. Be sure to save the CMOS setting when exit the CMOS. If the CPU is frequency multiplier locked, no CPU speed change will be seen even if the frequency multiplier setting in CMOS setup is changed. 21 Intel D2550-ITX series Motherboard Configuring the BIOS Enter BIOS Setup This section discusses how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided. The BIOS is the communication bridge between hardware and software. Correctly setting the BIOS parameters is critical to maintain optimal system performance. Refer to the following procedure to verify/change BIOS settings. 2. Press the Del key when the following message briefly displays at the bottom of the screen during the Power On Self Test (POST). q Core-Multi Processing Use this item to enable or disable Core-Multi processing. q Execute Disable Bit When disabled forces the XD feature flag to always return 0, defaults choose [Enable]. q Limit CPUID Maximum Allows you to determine whether to limit CPUID maximum value. Set this item to [Disable] Windows operating system; set this item to [Enable] for legacy operating system such as Windows NT4. 0. q Intel Virtualization Technology Hardware Virtualization Technology enables processor feature for running multiple simultaneous virtual machines allowing specialized software applications to run in full isolation of each other. CPU Configuration USB Configuration The items in this menu allow you to change the USB-related features. Press <enter> to display the configuration options: q USB Support Allows you to enable or disable USB support. q Legacy USB Support Allows you to enable or disable support for USB devices on legacy operating systems. q EHCI Hand-Off Allows you to enable support for operating systems without an EHCI hand-off feature. q USB transfer time-out Allows you to set USB transfer time-out. q Device reset time-out Allows you to set device reset time-out. q Device power-up delay Allows you to set device power-up delay. 25 Intel D2550-ITX series Motherboard Intel Fast Flash Standby The items in this menu allow you to change Intel Fast Flash standby features. [. . . ] The kit comes with a driver disk that contains utility drivers and additional software. The driver disk that has been shipped with your motherboard contains the following software and drivers: q Intel Chipset Driver q Realtek Sound Driver q Nvidia Graphics Driver q Realtek Network Driver q Etron USB 3. 0 Driver q Intel Wireless Driver q Bluetooth Driver Note: We reserve the right to update the driver version presented in the manual. The driver installation pictures shown in this section are for reference only. Drivers Installation 1. Insert the driver disk into the drive after loading your operating system, and then you can see the interface below. 32 Installing Drivers And Software 2. [. . . ]