User manual ZOTAC ZBOX NANO ID63 PLUS

[. . . ] · CMOS BT1: This button is for clear CMOS if you press this button on any environment. · DVI: Connects to monitor input. · VGA: Connects to monitor input. · eSATA:Connects to peripherial SATA devices. [. . . ] Install PCI card into slots "PCI1" or "PCI2" . - 10 - XFX Motherboard Series User Guide Chapter 3 Jumpers & Headers Setup 3. 1 Checking Jumper Settings · For a 2-pin jumper, plug the jumper cap on both pins will make it CLOSE (SHORT). Remove the jumper cap, or plug it on either pin (reserved for future use) will leave it at OPEN position. · For 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plugging the jumper cap in. How to identify the PIN1 jumpers?Please check the motherboard carefully, the PIN1 is marked by "1" or white thick line. 3. 2 CMOS Memory Clearing Header The time to clear the CMOS memory occurs when (a) the CMOS data becomes corrupted, (b) you forgot the supervisor or user password preset in the BIOS menu, (c) you are unable to boot-up the system because the CPU ratio/clock was incorrectly set in the BIOS menu, or (d) whenever there is modification on the CPU or memory modules. This header uses a jumper cap to clear the CMOS memory and have it reconfigured to the default values stored in BIOS. · Pins 1 and 2 shorted (Default): Normal operation. · Pins 2 and 3 shorted: Clear CMOS memory. JBIOSSLC · The button of CMOS_BT1 NC Dual_BIOS on back panel, if press this 1-2 Standard BIOS button on any environment, 2-3 Overclock BIOS the function is same with Pins 2 and 3 be shorted. · When the boot is from standard BIOS, the LEDA1 LED on board will light on; if the boot is from Overclock BIOS, the LEDB1 LED on board will light on. To clear the CMOS memory and load in the default values: 1. Set pin 2 and pin 3 shorted by the jumper cap. The BIOS setup screens and descriptions illustrated in this manual are for your reference only, and may not completely match with what you see on your screen. Do not change the BIOS parameters unless you fully understand its function. 4. 5. 1 CMOS Setup Utility After powering up the system, the BIOS message appears on the screen, when the first time or when CMOS setting wrong, there is following message appears on the screen , but if the first BIOS be setuped(or loaded default values) and save, the <DEL> key will be pressed if you will enter BIOS setup menu. Press F1 to Run SETUP If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt>+ <Del> keys, or by pressing the reset button on computer chassis. Only when these two methods should be fail that you restart the system by powering it off and then back on. After pressing <F1> or <Del> key, the main menu appears. BIOS SETUP UTILITY Security Power Main Advanced Boot JUSTwOOT! Exit System Overview System Information System Time System Date Floppy A Language Primary IDE Master : Primary IDE Slave : SATA Port 1 : SATA Port 3 : SATA Port 2 : SATA Port 4 : USB Device [00:42:05] [Sun 11/04/2007] [Disabled] [English] [Not Detected] [Not Detected] [Not Detected] [Not Detected] [Not Detected] [Not Detected] Use [ENTER] , [TAB] or [SHIF-TAB] to select a eld. Use [+] or [-] to con gure system time. +Tab F1 F10 ESC Select Screen Select Item Change Field Select Field General Help Save and Exit Exit v02. 61 (C)Copyright 1985-2006, American Megatrends, Inc. This is the System Overview, The System Time, System Date, Primary IDE information, SATA port information and Memory size display. IDE Configuration Click <Press Enter> key to enter its submenu, it will be display IDE configuration, also you can set the ATA/IDE, SATA function from the options and set the IDE boot order, or set it as IDE Master, Slave within them. Floppy Configuration Click <Press Enter> key to enter its submenu, it will be display floppy configuration, and this item sets the type of floppy drives installed. - 17 - XFX Motherboard Series 4. 5. 2 Control Keys User Guide Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. Please check the following table for the function description of each control key. Control Key(s) / / +/ -/PU/PD <Enter> <ESC> <F1> <F2/F3> <F5> <F7> <F8> <F9> <F10> Function Description Move cursor left or right to select Screens Move cursor up or down to select items To Change option for the selected items To bring up the selected screen Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu General help Change Colors Restore the previous CMOS value from CMOS, only for Option Page Setup Menu Discard Changes Load Failsafe Defaults Load Optimal Defaults Save configuration changes and exit setup - 18 - XFX Motherboard Series 4. 5. 3 Advanced Setting Main Advanced Boot BIOS SETUP UTILITY Security Power JUSTwOOT!Exit User Guide Advanced Settings WARNING: Setting wrong values in below sections may cause system to malfunction. CPU Con guration Chipset Onboard Devices PCIPnP Con gure CPU. Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit v02. 61 (C)Copyright 1985-2006, American Megatrends, Inc. [. . . ] F10 key can be used for this operation. Load Optimal Defaults Load Failsafe Defaults Save con guration changes and exit setup?[Ok] [Ok] [Cancel] Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit v02. 61 (C)Copyright 1985-2006, American Megatrends, Inc. Discard Changes and Exit Highlight this item and select <Ok>, then press <Enter> to discard any changes that you have made in the Setup Utility and exit the Setup Utility. Or press <Cancel> to return to the main menu. [. . . ]