User manual ZOTAC ZBOX NANO XS AD13 PLUS

[. . . ] ™™ Set up the system on a stable surface with the provided stand. Never use the system alone without the stand. ™™ Openings on the chassis are for ventilation. Make sure you leave plenty of space around the system for ventilation. [. . . ] HDMI output The HDMI (High Definition Multimedia Interface) output supports Full HD 1080p displays such as an HDTV or monitor. USB3. 0 ports The USB3. 0 ports support the SuperSpeed USB3. 0 devices and are backwards compatible with USB2. 0/1. 1 devices. Use the ports for USB3. 0 devices for maximum performance with USB3. 0 compatible devices. Ethernet port The eight-pin RJ-45 LAN port supports standard Ethernet cable for connection to a local area network (LAN) with speeds of 10/100/1000Mbps. USB2. 0 ports The USB (Universal Serial Bus) 2. 0 ports are compatible with USB2. 0 devices such as keyboards, mice, cameras and hard disk drives. 7 ZOTAC ZBOX nano XS BIOS settings of specific functions ZOTAC ZBOX nano XS has some specific functions which can be enabled or disabled in BIOS settings, such as LED indicator, USB2. 0 charge and CIR controller. How to disable the ring LED indicator 1. Turn on the ZBOX nano mini-PC, then press <Delete> to enter the BIOS SETUP UTILITY. 2. Use the arrow keys to navigate to the Advanced menu and select Onboard Device Config. 8 ZOTAC ZBOX nano XS 3. Press <Enter> to display the Onboard Device Control and navigate to Backlight Control. 4. Press <Enter> and select Disabled. 5. Press F10 to save the configuration and exit. 9 ZOTAC ZBOX nano XS How to enable USB2. 0 charge (for S3/S4 status) 1. In Advanced menu, select Onboard Device Config and press <Enter>. 2. Use the arrow keys to enter the item Rear USB2. 0 Charge hotplug(Top/ Bottom) / Front USB2. 0 Charge hotplug, and select Enabled. 3. Press F10 to save the configuration and exit. Note: Before charging via USB2. 0 in S5 status, please make sure the Deep S5 (Deep S5 in PowerManage menu) is disabled. 10 ZOTAC ZBOX nano XS How to disable CIR controller (for internal IR receiver) 1. Use the arrow keys to navigate to Advanced > OnBoard Device Config > CIR Controller Configuration. 2. Enter CIR Controller and select Disabled. Enabled: enable the internal IR receiver (default) Disabled: disable the internal IR receiver 3. Press F10 to save the configuration and exit. 11 ZOTAC ZBOX nano XS Customizing the ZOTAC ZBOX nano XS Please follow the instructions below to remove the cover of the ZOTAC ZBOX nano XS before customizing. Loosen the 4 screws securing the bottom cover into place. 2. Gently remove the cover. 12 ZOTAC ZBOX nano XS Installing a memory module 1. Locate the SO-DIMM memory slot and insert a SO-DIMM memory module into the slot at a 45 degree angle. 2. Gently press down on the memory module until it locks into place by the arms of the memory slot. 13 ZOTAC ZBOX nano XS Installing an mSATA 1. Insert the mSATA into the slot and gently slide into the connector. 2. Install the screws of the mSATA. 14 ZOTAC ZBOX nano XS Connecting a SPDIF cable 1. Connect the SPDIF cable to the headphone/SPDIF adapter correctly. 2. Locate the front panel and connect the headphone/SPDIF adapter to the headphone/SPDIF jack. 15 ZOTAC ZBOX nano XS Setting up the ZOTAC ZBOX nano XS Please connect the peripherals before using the ZOTAC ZBOX nano XS. 1 2 3 4 5 1. Turning on the system Connect the supplied AC adapter to the DC IN jack on the system rear panel and then press the power switch on the front panel to turn on the system. Follow the instructions below to use the remote control. Function keys Navigation Buttons OK START OK Playback Buttons i RECORD    BACK PAUSE   = STOP   INFORMATION  UP  DOWN  LEFT  RIGHT REW  PLAY FWD REPLAY SKIP Shortcut Buttons | GUIDE SLEEP WAKE Audio and Video Buttons +  + - 1 4 7 *. CLEAR Numeric Keypad 2 5 8 0 Teletext Buttons T BLUE 3 6 9 # ENTER -    VOLUME UP / DOWN MUTE CHANNEL UP / DOWN RED TELETEXT GREEN YELLOW Note: Some remote control functions listed above are only available with the relative hardware equipments. If the hardware equipments you adopt are not compatible with the system, you are unable to use these functions. The ZOTAC ZBOX nano XS is designed to meet MCE standards. [. . . ] Select “Set up my connection manually”. 7. Select your connection type and click “Next”. 8. Enter your ISP Name and click “Next”. 10. Click “Finish” to finish the configuration. [. . . ]