User manual ZYXEL ES-315-F QUICK GUIDE V3.70

[. . . ] · Only trained and qualified personnel should install or replace transceivers. · SFP transceivers are sensitive to static. To prevent damage from electrostatic discharge (ESD), use an ESD preventive wrist strap when you install or remove a SFP transceiver. · Avoid getting dust and other contaminants into the optical bores. 3 ES-315-F Quick Start Guide · SFP transceivers are equipped with a Class 1 laser, which emits invisible radiation when the device or system is powered up. [. . . ] This ensures that your computer can communicate with your ES-315-F. The following instructions are for the Windows 2000, Windows NT and Windows XP operating systems. 1 In Windows XP, click Start > Control Panel. In Windows 2000/NT, click Start > Settings > Control Panel. 2 In Windows XP, click Network Connections. In Windows 2000/NT, click Network and Dial-up Connections. 3 Right-click Local Area Connection and then click Properties. 4 Select Internet Protocol (TCP/IP) (under the General tab in Windows XP) and click Properties. 5 The Internet Protocol TCP/IP Properties screen opens (the General tab in Windows XP). 12 ES-315-F Quick Start Guide Note down your computer's current IP settings before you change them. You may need them later. 6 Select Use the following IP address and fill in the IP address (choose one in the range 192. 168. 1. 2 192. 168. 1. 254), Subnet mask (255. 255. 255. 0), and Default gateway (192. 168. 1. 1) fields. 7 Click OK to close the Internet Protocol (TCP/IP) Properties window. 8 Click Close (OK in Windows 2000/NT) to close the Local Area Connection Properties window. 13 ES-315-F Quick Start Guide Close the Network Connections window. 3 Log In To the Web Configurator Take the following steps to access the ES-315-F for initial configuration. Use Internet Explorer 6. 0 and later versions or Netscape Navigator 7. 0 and later versions with JavaScript enabled and pop-up blocking disabled. Open an Internet browser (such as Internet Explorer or Netscape Navigator). Enter the ES-315-F's IP address in the address bar. The ES-315-F's default IP address is 192. 168. 1. 1. 14 ES-315-F Quick Start Guide A window similar to the following appears. Enter the default username (admin) and the default password (1234). Click OK. If you do not see this screen, make sure that your Internet browser allows pop-up windows (in Internet Explorer, select Tools > Pop-up Blocker and then select Turn Off Pop-up Blocker). If this does not help, make sure the IP addresses and subnet masks of the ES-315-F and the computer are in the same IP address range (see section 2. 4). 15 ES-315-F Quick Start Guide The Status screen displays. 4 Set the Password For security reasons, you should change the password when you first log in. Take the following steps to do this. 16 ES-315-F Quick Start Guide 1 Click Management in the navigation panel on the left of the screen. In the menu that displays, click Access Control. Then, click Logins. 2 The following screen displays. 3 Enter the login information you want to use, as follows. The password is case sensitive - "ABCD" is not the same as "abcd". 17 ES-315-F Quick Start Guide · Enter the default password (1234) in the Old Password field. · Choose a new password up to 31 characters in length (letters, numerals, spaces, dashes (-) and underscores (_) are allowed) and enter it in the New Password field. An asterisk (*) displays for each character you enter. Be sure to record the new password and keep it in a safe place. If you forget this information, you will need to reset the ES-315-F to its factory defaults (press the Reset button in for 3 ~ 5 seconds). · Re-enter the new password in the Re-type to confirm field. [. . . ] 2 Drill two holes for the screws, exactly 104 mm apart. Be careful to avoid damaging pipes or cables located inside the wall when drilling holes for the screws. 22 ES-315-F Quick Start Guide 3 Do not insert the screws all the way into the wall. Leave a small gap of about 0. 5 cm between the heads of the screws and the wall. 4 Make sure the screws are snugly fastened to the wall. They need to hold the weight of the ES-315-F with the connection cables. [. . . ]