User manual ZYXEL GS2200-48

[. . . ] GS2200-48 Intelligent Layer 2 Switch Default Login Details IP Address http://192. 168. 0. 1 (Out-of-band MGMT port) http://192. 168. 1. 1 (In-band ports) User Name Password admin 1234 Firmware Version 3. 80 Edition 1, 7/2009 www. zyxel. com www. zyxel. com Copyright © 2009 ZyXEL Communications Corporation About This User's Guide About This User's Guide Intended Audience This manual is intended for people who want to configure the Switch using the web configurator or via commands. Related Documentation · Web Configurator Online Help Embedded web help for descriptions of individual screens and supplementary information. · Command Reference Guide The Command Reference Guide explains how to use the Command-Line Interface (CLI) and CLI commands to configure the Switch. Note: It is recommended you use the web configurator to configure the Switch. · Supporting Disc Refer to the included CD for support documents. · ZyXEL Web Site Please refer to www. zyxel. com for additional support documentation and product certifications. Documentation Feedback Send your comments, questions or suggestions to: techwriters@zyxel. com. tw Thank you!The Technical Writing Team, ZyXEL Communications Corp. , 6 Innovation Road II, Science-Based Industrial Park, Hsinchu, 30099, Taiwan. Disclaimer Graphics in this book may differ slightly from the product due to differences in operating systems, operating system versions, or if you installed updated firmware/software for your device. [. . . ] Refer to Section 18. 2 on page 149 for more information. 158 GS2200-48 User's Guide Chapter 19 Policy Rule Click Advanced Applications > Policy Rule in the navigation panel to display the screen as shown. Figure 71 Advanced Application > Policy Rule GS2200-48 User's Guide 159 Chapter 19 Policy Rule The following table describes the labels in this screen. Table 48 Advanced Application > Policy Rule LABEL Active Name Classifier(s) DESCRIPTION Select this option to enable the policy. Enter a descriptive name for identification purposes. This field displays the active classifier(s) you configure in the Classifier screen. Select the classifier(s) to which this policy rule applies. To select more than one classifier, press [SHIFT] and select the choices at the same time. Parameters Set the fields below for this policy. You only have to set the field(s) that is related to the action(s) you configure in the Action field. General Egress Port Priority DSCP TOS Metering Type the number of an outgoing port. Specify a DSCP (DiffServ Code Point) number between 0 and 63. Specify the type of service (TOS) priority level. You can configure the desired bandwidth available to a traffic flow. Traffic that exceeds the maximum bandwidth allocated (in cases where the network is congested) is called out-of-profile traffic. Bandwidth Specify the bandwidth in kilobit per second (Kbps). Out-ofProfile DSCP Action Specify the action(s) the Switch takes on the associated classified traffic flow. Forwarding Select No change to forward the packets. Select Discard the packet to drop the packets. Select Do not drop the matching frame previously marked for dropping to retain the frames that were marked to be dropped before. Priority Select No change to keep the priority setting of the frames. Select Set the packet's 802. 1 priority to replace the packet's 802. 1 priority field with the value you set in the Priority field. Select Send the packet to priority queue to put the packets in the designated queue. Select Replace the 802. 1 priority field with the IP TOS value to replace the packet's 802. 1 priority field with the value you set in the TOS field. Specify a new DSCP number (between 0 and 63) if you want to replace or remark the DSCP number for out-of-profile traffic. 160 GS2200-48 User's Guide Chapter 19 Policy Rule Table 48 Advanced Application > Policy Rule (continued) LABEL Diffserv DESCRIPTION Select No change to keep the TOS and/or DSCP fields in the packets. Select Set the packet's TOS field to set the TOS field with the value you configure in the TOS field. Select Replace the IP TOS with the 802. 1 priority value to replace the TOS field with the value you configure in the Priority field. [. . . ] This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this device in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CE Mark Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Taiwanese BSMI (Bureau of Standards, Metrology and Inspection) A Warning: Notices Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This Class A digital apparatus complies with Canadian ICES-003. [. . . ]