User manual ZYXEL IES-1248-51A

[. . . ] Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice. Trademarks Trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners. ii Copyright IES-1248-51A Hardware Installation Guide ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two (2) years from the date of purchase. During the warranty period and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. [. . . ] Here are descriptions of three typical installation scenarios. See the Notes About MDFs (Main Distribution Frames) for more information about MDFs. Use telephone wires with RJ-11 jacks on one end (follow the pin assignments shown in the Pin Assignments Appendix) for connecting to the AAM1008. 4. 4. 2 Installation Scenario A You want to install the AAM1008 network module in an environment where there are no previously installed MDFs. There is no phone service and you want to install the AAM1008 for data-access only. No connections from the CO ports are necessary. You may connect using an MDF or attach RJ-11 connectors to the non-AAM1008 side of the telephone wire and then connect to ADSL modem directly. 4-6 Hardware Connections IES-1248-51A Hardware Installation Guide Figure 4-7 Installation Scenario A Procedure To Connect To An MDF Step 1. Step 3. Connect the RJ-11 connector end of a telephone wire to one of the USER ports on the AAM1008. Connect the other end of the telephone wire to the upper ports of the MDF using a punch-down tool. Connect the telephone wiring from each end-user's ADSL modem to the lower ports of the MDF. 4. 4. 3 Installation Scenario B Phone service is available. There is one MDF from which end-users CO connections are made (see next figure). Hardware Connections 4-7 IES-1248-51A Hardware Installation Guide Figure 4-8 One MDF for End-user and CO Connections Please refer to the following figure for the connection schema. MDF 1 is the original MDF used for telephone connections only. Connect the other ends of the telephone wires to the lower ports of MDF 4 using a punch-down tool. Connect the top ports of MDF 4 to the bottom ports of MDF 1 using regular telephone wires. Step 8. Hardware Connections IES-1248-51A Hardware Installation Guide Connect the top ports of MDF 1 to the telephone company. 4. 4. 5 LAN Port (Ethernet) Connection Connect the LAN port of your SAM1008 to an Ethernet WAN switch using a straight-through Category 5 UTP (Unshielded Twisted Pair) cable with RJ-45 connectors. Connect the other end of the cable to an Ethernet switch. You may stack multiple IES-1248-51A units up to the number of ports available on the Ethernet switch as shown next. Figure 4-12 Stacking Multiple IES-1248-51A Units 4. 4. 6 Power Cord Connect the female end of the power cord to the power receptacle on the front panel of your IES-1248-51A (to the right of the fuse housing) as shown next. Connect the other end of the cord to a power outlet. Make sure that no objects obstruct the airflow of the fans (locatd on the side of the unit). 4-12 Hardware Connections IES-1248-51A Hardware Installation Guide Make sure you use a 100-240VAC/1A, 50/60Hz power source. Figure 4-13 Connecting the Power Cord to the IES-1248-51A and a Power Source Hardware Connections 4-13 IES-1248-51A Hardware Installation Guide Chapter 5 Turning On Your IES-1248-51A This chapter discusses the fans and LEDs of the IES-1248-51A after you turn it on. 5. 1 · · Introduction Have attached a computer to the IES-1248-51A serial port as explained previously. Can see the status LEDs on the front panel while you view the VT100 terminal emulator. Before turning on your IES-1248-51A, make sure you: Push the power switch (located at the front of the IES-1248-51A) to the ON or "|" position. The IES-1248-51A will automatically run a self-test that takes approximately 20 seconds. The SYS LED will remain on if your IES-1248-51A has started normally. If the SYS LED does not turn on then recheck your connections or refer to the Hardware Troubleshooting chapter. [. . . ] 2-1 Hardware Specifications Operating Environment - Humidity . . . . . . . . . . . . . . . . . . . . . . G Operating Environment - Temperature . . . . . . . . . . . . . . . . . G Storage Environment - Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . G Storage Environment - Temperature. . . . . . . . . . . . . . . . . . . . . G Hardware Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Index I IES-1248-51A Hardware Installation Guide I IES-1248-51A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii Installing a Network Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Installing Fuses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C Integrated Ethernet Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii L LED DSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2, 6-3 Lightening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F M M3 flat head screws. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 M5 flat head screws. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]