User manual ZYXEL IES-5000M

[. . . ] IES-5000 Series Integrated Ethernet Switch User's Guide Version 3. 01 8/2007 Edition 1 www. zyxel. com About This User's Guide About This User's Guide Intended Audience This manual is intended for people who want to install and maintain the IES-5000 series Integrated Ethernet Switch. This User's Guide gives hardware installation, connection and maintenance instructions. Related Documentation · Line Card User's Guides These User's Guides provide hardware connection details and explain how to configure and manage the individual line cards. · Management Switch Card User's Guide This User's Guide provides hardware connection details, and configuration and management instructions for the management switch card. · Supporting Disk Refer to the included CD for support documents. [. . . ] See Section 2. 5. 4 on page 43 for example splitter chassis rear panel connections. 2. 4. 5 Splitter Chassis Rear Panel Connections (VoIP) When using the VoIP line card in conjunction with an ADSL or VDSL card and its associated splitter card(s), connect the VoIP line card's extension card(s) and the DSL splitter card(s) as follows. IES-5000 Series User's Guide 41 Chapter 2 Hardware Installation and Connections Figure 21 DSL and VoIP Rear Panel Telco-50 Connections (2 Splitter Chassis) ASC1024 SEC1024 · Connect the USER Telco-50 connector from the extension card attached to the VoIP line card's 1 ~ 24 ports to the CO Telco-50 connector of the splitter card attached to the DSL line card's 1 ~ 24 ports. · Connect the USER Telco-50 connector from the extension card attached to the VoIP line card's 25 ~ 48 ports to the CO Telco-50 connector of the splitter card attached to the DSL line card's 25 ~ 48 ports. When you do not use the VoIP line card in conjunction with a DSL splitter card, connect the USER Telco-50 connectors to the subscribers' telephone wiring. In most multi-tenant unit applications, the USER pins connect to the subscribers' telephone wiring via a Main Distribution Frame (MDF). 2. 5 MDF Connections This section shows you how to connect the IES-5000 splitter chassis to a Main Distribution Frame. 2. 5. 1 MDF Connections Overview Observe the following before you start: · Refer to Appendix A on page 73 for the gauge of telephone wire to use. · Follow the pin assignments shown in the line card User's Guide to wire Telco-50 cables to Telco-50 connectors. 2. 5. 2 MDF (Main Distribution Frame) An MDF is usually installed between subscribers' equipment and the telephone company (CO) in a basement or telephone room. The MDF is the point of termination for the outside telephone company lines coming into a building and the telephone wiring in the building. 42 IES-5000 Series User's Guide Chapter 2 Hardware Installation and Connections Figure 22 MDF (Main Distribution Frame) Wiring · Connect wiring to end-user equipment to the lower ports of an MDF and connect wiring from the telephone company to the upper ports of an MDF (see the previous figure). · Some MDFs have surge protection circuitry built in between the two banks; thus, do not connect telephone wires from the telephone company directly to your IES-5000. · Use a punch-down tool to seat telephone lines into MDF blocks. 2. 5. 3 Telco-50 Cables Telco-50 cables are used for data and voice applications with MDFs (Main Distribution Frame), patch panels and distribution boxes. They can also be used as extension cables. Telco50 cables are made up of 25 twisted-pair copper wires. Connect a Telco-50 connector to one end of the cable (see Section 2. 5. 3 on page 43 for pin assignments) and connect the other end directly to an MDF; alternatively attach RJ-11 connectors and connect directly to DSL modems or telephones. Figure 23 Telco-50 Cable with RJ-11 Connectors 2. 5. 4 MDF Connections The following section gives an overview of possible installation scenarios for the IES-5000 using the line cards and splitter cards. Data and voice signals can coexist on the same telephone wiring. IES-5000 Series User's Guide 43 Chapter 2 Hardware Installation and Connections Figure 24 Installation Overview Example You can also attach RJ-11 connectors to the Telco-50 cable and connect directly to a DSL modem(s), a telephone(s) or a patch panel. This chapter discusses connections using MDFs. The following sections describe typical installation scenarios. 2. 5. 4. 1 MDF Installation Scenario A You want to install the IES-5000 in an environment where there are no previously installed MDFs. There is no phone service and you want to install the IES-5000 for data-access only. No connection from the Telco-50 CO connector is necessary. G. SHDSL connections carry data only, thus they are best suited to this installation scenario. You can connect using an MDF or attach RJ-11 connectors to the non-IES-5000 end of the Telco-50 cable and then connect to DSL modems or telephones directly. 44 IES-5000 Series User's Guide Chapter 2 Hardware Installation and Connections Figure 25 Installation Scenario A Use the following procedure for this MDF installation scenario. 1 Connect the Telco-50 connector end of the cable to the Telco-50 connector labeled USER. 2 Connect the wiring on the other end of the Telco-50 cable to the upper ports of the MDF using a punch-down tool. 3 Connect the telephone wiring from each end-user's DSL modem to the lower ports of the MDF. [. . . ] Viewing Certifications 1 Go to http://www. zyxel. com. 2 Select your product on the ZyXEL home page to go to that product's page. 3 Select the certification you wish to view from this page. ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating 78 IES-5000 Series User's Guide Appendix B Legal Information condition. [. . . ]