User manual ZYXEL M-102

[. . . ] ZyXEL M-102 802. 11g Wireless MIMO CardBus Card User's Guide Version 2. 00 Edition 1 3/2006 ZyXEL M-102 User's Guide Copyright Copyright © 2006 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. [. . . ] This fields displays the network standard (802. 11g or 802. 11b) of the wireless device. This field displays the channel number used by each wireless device. This field shows whether data encryption is activated (WEP (WEP or 802. 1x), WPA or WPA-PSK) or inactive (DISABLE). This field displays the MAC address of the wireless device. This field displays the time when the wireless device is scanned. 3. 2. 1 Connecting to a WLAN Network Follow the steps below to connect to a WLAN network using the Site Survey screen. 1 Click Scan to search for all available wireless networks within range. 2 To join a network, click an entry in the table to select a wireless network and then click Connect or double-click an entry. 3 If the WEP encryption is activated for the selected wireless network, the Security Settings screen displays. You must set the related fields in the Security Settings screen to the same security settings as the associated wireless device. Refer to Section 3. 2. 2 on page 36 for more information. Otherwise click the Back or Exit button and connect to another wireless network without data encryption. 4 Verify that you have successfully connected to the selected network and check the network information in the Link Info screen. 3. 2. 2 Security Settings When you configure the M-102 to connect to a network with wireless security activated and the security settings are disabled on the M-102, the screen varies according to the encryption method used by the selected network. 36 Chapter 3 ZyXEL Utility Configuration ZyXEL M-102 User's Guide 3. 2. 2. 1 WEP Encryption Figure 15 Security Settings: WEP The following table describes the labels in this screen. Table 6 Security Settings: WEP LABEL WEP Authentication Type Pass Phrase DESCRIPTION Select 64 Bits, 128 Bits or 152 Bits to activate WEP encryption and then fill in the related fields. Choices are Auto Switch, Open and Shared. Refer to Section 2. 3 on page 31 for more information. Enter a passphrase of up to 63 case-sensitive printable characters. As you enter the passphrase, the M-102 automatically generates four different WEP keys and displays it in the key field below. Refer to Section 2. 2. 1 on page 28 for more information. At the time of writing, you cannot use passphrase to generate 152-bit WEP keys. Select a default WEP key to use for data encryption. The key displays in the field below. Transmit Key Chapter 3 ZyXEL Utility Configuration 37 ZyXEL M-102 User's Guide Table 6 Security Settings: WEP (continued) LABEL DESCRIPTION Key x (where x is a Select this option if you want to manually enter the WEP keys. Enter the WEP key number between 1 in the field provided. and 4) If you select 64 Bits in the WEP field. [. . . ] If they do not match, it is assumed that the data has been tampered with and the packet is dropped. By generating unique data encryption keys for every data packet and by creating an integrity checking mechanism (MIC), with TKIP and AES it is more difficult to decrypt data on a Wi-Fi network than WEP and difficult for an intruder to break into the network. The encryption mechanisms used for WPA(2) and WPA(2)-PSK are the same. The only difference between the two is that WPA(2)-PSK uses a simple common password, instead of user-specific credentials. [. . . ]