User manual ZYXEL NWA-3100

[. . . ] Ensure your computer's network card is working properly. 2 Access the Web Configurator Use Internet Explorer 6. 0 and later or Netscape Navigator 7. 0 and later versions with JavaScript enabled. 3 ENGLISH 2. 1 Set Up Your Computer's IP Address You must first set your computer to use a static IP address in the 192. 168. 1. 3 192. 168. 1. 254 range with a subnet mask of 255. 255. 255. 0. This ensures that your computer can communicate with your NWA-3100. The following instructions are for the Windows 2000, Windows NT and Windows XP operating systems. 1 In Windows XP, click Start > Control Panel. [. . . ] SSID03's default SSID (the name of the network) is ZyXEL03 and its default Security setting is Security01. If the settings are different, or if you want to change the SSID, select SSID03 and click Edit to change the settings. 8 ENGLISH 7 Click the Security tab. Ensure that Security01 is selected and click Edit. 8 This is where you can enter the security settings for your wireless network. The fields you fill in differ according to the type of security you select in the Security Mode field. Select None if you do not wish to use wireless security. This example uses WPA2-PSK security, in which all wireless clients must use the same preshared key to join the network. Ensure that all your wireless clients can use the type of security you set. If you have an IP address to use, select Use fixed IP address and enter it along with the subnet mask and gateway IP address. Otherwise, select Get automatically from DHCP. Click Apply. 9 ENGLISH 10 Change the wireless settings in the wireless stations to match those of the NWA3100. Refer to your wireless adapter's documentation. If you change the NWA-3100's IP address, you must use the new IP address when you next access the web configurator. The device is now ready to connect to your wired network. You can do this now, or once you have installed the hardware. If the wireless clients cannot access the wired network, verify that the IP address and the subnet mask of the NWA-3100 and the computers on the network are in the same range. If the ETHN LED is off, check the cables between the NWA-3100 and your computer or hub. 4 Install the Hardware 4. 1 Attaching Antennas When facing the front of the NWA-3100, the right antenna (main antenna) transmits and receives; the left antenna only receives. 1 Screw the antennas clockwise onto the antenna connectors on the sides of your NWA-3100. The antennas should be perpendicular to the ground and parallel to each other. Make sure the antennas are securely screwed onto the antenna connectors. 10 ENGLISH 4. 2 Hardware Mounting In general, the best location for the access point is at the center of your intended wireless coverage area. For better performance, mount the NWA-3100 high up in an area that is free of obstructions. Free-standing Lie your NWA-3100 on a flat, level surface (a desk or shelf, for example) that is strong enough to support the weight of the NWA-3100 with connection cables. Wall-mounted Do the following to attach your NWA-3100 to a wall. 1 Screw two screws (not included) into the wall 60mm apart (see the figure in step 3). Use screws with 6mm ~ 8mm (0. 24" ~ 0. 31") wide heads. Do not screw the screws all the way in to the wall; leave a small gap between the head of the screw and the wall. The gap must be big enough for the screw heads to slide into the screw slots and the connection cables to run down the back of the NWA-3100. Make sure the screws are securely fixed to the wall and strong enough to hold the weight of the NWA-3100 with the connection cables. 2 Adjust the cables. [. . . ] Klicken Sie bei Windows 2000/NT auf Network and Dial-up Connections (Netzwerk- und DFÜ-Verbindungen). 3 Klicken Sie mit der rechten Maustaste auf Local Area Connection (LAN-Verbindung) und dann auf Properties (Eigenschaften). 4 Wählen Sie Internet Protocol (TCP/IP) (Internetprotokoll (TCP/IP) (bei Windows XP auf der Registerkarte General (Allgemein)), und klicken Sie auf Properties (Eigenschaften). Wählen Sie einen Namen oder belassen Sie diesen als Standard. [. . . ]