User manual ZYXEL OMNI 56K USB

[. . . ] User's Guide for ZyXEL Omni 56K USB Modem ZyXEL TOTAL INTERNET ACCESS SOLUTIONS ZyXEL Communications Corporation User's Guide for ZyXEL Omni 56K USB Modem ZyXEL Omni 56K USB Modem Trademarks: Product and corporate names mentioned in this publication are used for identification purposes only and may be properties of their respective owners. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, guide, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. Disclaimer: ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. [. . . ] 38 ATX7, error control result code is enabled. 0 Display result code in numeric format. (see S35. 7) 40 Display result code in verbose format. (Default) 80 Modem does not return result code. (see also S40. 1) hex Bit-mapped register. 10-70 Speaker volume control, increments of 16 in decimal value. &S0 &S1 &C0 &C1 &R0 &R1 &D0 &D1 &D2 192 S23= bit 0 1 2 3-5 dec 0 1 0 2 0 4 0 8 16 24 32 40 48 56 0 64 0 128 dec 16112 &D3 +105 E0 E1 T P &P0 &P1 X0 X1 X2 X3 X4 X5 X6 X7 V0 V1 Q0 Q1 L0-7 6 7 S24= bit 6-4 5-25 User's Guide for ZyXEL Omni 56K USB Modem S25= 0 to 255 0-FF Specify the time delay that DTR signal needs to be OFF before it is recognized, in 10 ms units. If S25=0, the delay time is set to 4 ms. 0 to 0-FF Set the delay, in 10 millisecond units between the 255 RTS and modem's CTS response in synchronous mode. (see `&Rn' command) dec hex Bit-mapped register. 1 1 MNP4 + MNP3 (see also S41. 0) 2 2 MNP4 + MNP5 (see also S38. 5, S41. 0) 3 3 V. 42+MNP4 4 4 V. 42 + V. 42bis (compatible with &K2) (Default) 0 0 Flow control disabled. (Default) 32 20 Software (XON/XOFF) flow control. 64 40 Retrain action taken if signal quality is poor. 128 80 Adaptive rate (auto fall-back/forward) when signal quality changes. (Default) 192 C0 Disconnect when signal quality is poor. (Default) 10 8 Non-destructive, un-expedited break. (See also S18, S44b6) 1 64 DTE/DCE rate is fixed at the DTE setting, range from 300 to 460. 8 Kbps. (Default, also see S18, S44b6) 0 to 3 0 to 3 Set default dial phone number pointer, use AT&Zn=s to store phone numbers in EEPROM. 0-255 0-FF Holds the ASCII decimal value of the XON. 0-255 0-FF Holds the ASCII decimal value of the XOFF. +000 S26= +000 &Rn S27= Bit 0-2 +156 &K0 &K1 &K2 &K3 &K4* &H0 &H3 &H4 &H5 *Q0 *Q1 *Q2 *Q3 +068 &Y0 &Y1 &Y2 &G0 &G1 &G2 &B0 &B1 +000 *D +017 +019 +032 3-5 6-7 S28= bit 2-3 4-5 6 S29= S31= S32= S35= bit 5-26 User's Guide for ZyXEL Omni 56K USB Modem 1 3 5 7 2 8 32 128 2 8 20 80 Disable aborting from terminal during modem handshaking. Add 16dB attenuation to the leased line transmission power. [. . . ] 5-10 Extended AT& Command Sets . . . . . . . . . . . . . . . . . . . 5-4 Extended AT* Command Sets . . . . . . . . . . . . . . . . . . . . 5-8 Fax Command Sets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 Fax Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]