User manual ZYXEL P-660HW-DX V2 QUICK GUIDE V3.40

[. . . ] Wait a couple of minutes while your device checks the connection. If any of these lights are not on, check your connections and inspect your cables for damage. If the lights are still off, contact your local vendor. 2 Internet Connection Setup: Automatic Use this section to have your P-660HW-Dx v2 automatically detect and set up your Internet connection. Wait while your P-660HW-Dx v2 tries to detect your DSL connection to your ISP. [. . . ] Click Next. 3) If you select either WEP or WPA-PSK security (recommended), then follow the directions to enter the appropriate key. Click Next to continue and Apply to save your wireless LAN settings. 7 P-660HW-Dx v2 Quick Start Guide 4 Check your configuration and write down your wireless LAN settings for later use. Click Finish to complete and save the wizard setup. 5 Your Internet is ready for you to use. Open your browser and navigate to your favorite website. 6 Internet Connection Setup Using Advanced Settings Use this section to set up your Internet connection manually if you do not see the ISP Parameters for Internet Access screen when you run the wizard (see section 4, step 4). (Follow steps 1 to 5 in section 3. ) 2 Select Go to Advanced setup. Click Network > WAN in the navigation panel on the left of the screen. 4) Enter the information exactly as provided by your ISP. Click Apply. 8 P-660HW-Dx v2 Quick Start Guide Note: The fields available in this screen depend on the Mode and Encapsulation you select 5 If you still cannot access the Internet, see Troubleshooting and/or contact your Internet Service Provider (ISP) for assistance. 7 Setting Up a Wireless Network with OTIST 7. 1 About OTIST ZyXEL's One-Touch Intelligent Security Technology (OTIST) feature allows you to automatically configure the SSID and WPA-PSK on all OTIST-equipped wireless clients within range of the P660HW-Dx v2. Enable OTIST only if your wireless clients support WPA and OTIST. You should have already configured wireless settings on the P-660HW-Dx v2 using the wizard. If you select Disable wireless security using the wireless wizard, the P-660HW-Dx v2 will create a WPA-PSK automatically. If you select Manually assign a WEP key using the wireless wizard, the P-660HW-Dx v2 will replace the WEP key with a WPA-PSK. You must enable OTIST on the P-660HW-Dx v2 and all wireless clients within three minutes in any order. 9 P-660HW-Dx v2 Quick Start Guide 7. 2 Enabling OTIST To enable OTIST on the P-660HW-Dx v2, you can either use the wizard (see section 3) or hold in the RESET button (see section 1) for about three seconds. Do not hold the RESET button in for too long, as this will reset the P-660HW-Dx v2 to the factory defaults. To enable OTIST on wireless clients, click Start in the Adapter screen. If you have previously saved a setup key on the P-660HW-Dx v2, use it instead of the default. For more information, see Wireless LAN in the User's Guide. Troubleshooting 1 If you cannot access the web configurator, · Your computer may be set to use a static IP address in a different subnet from the ZyXEL device. See the appendix in the User's Guide for information on setting up your IP address. · If you are using Internet Explorer in Windows XP or Windows Server 2003, make sure you allow pop-up windows, JavaScripts and Java permissions or set the Internet security level lower than High in Internet Explorer (in Internet Explorer, click Tools > Internet Options > Security > Custom Level. . . ). See the appendix in the User's Guide for more information. 2 If you cannot access the Internet when your computer is connected to the ETHERNET port, follow these steps. If they are different from what is described in section 1, make sure the P-660HW-Dx v2 is correctly connected. (See section 1. ) If the lights are still different, turn off the device, wait a few seconds, and turn it on again. [. . . ] Check whether you can access the Internet. If you still cannot access the Internet, contact your Internet Service Provider. 3 If you cannot access the Internet using the wireless network, follow these steps. A) On a computer in the wireless network, open your browser, and go to http://192. 168. 1. 1. [. . . ]