User manual ZYXEL P-791R

[. . . ] Set this switch to the "CON" side to use the CON/AUX port as a console port for local device configuration and management. Connect the 9-pin male end of the console cable to the console port of the Prestige and the other end to a serial port (COM1, COM2 or other COM port) on your computer. Your computer should have a terminal emulation communications program (such as HyperTerminal) set to VT100 terminal emulation, no parity, 8 data bits, 1 stop bit, no flow control and 9600 bps port speed. Set this switch to the "AUX" side to use the CON/AUX port as an auxiliary dial-up WAN connection. [. . . ] If you have more than two DNS servers, click Advanced, the DNS tab and then configure them using Add. 5 Prestige 791R 6. Remove any previously installed gateways in the IP Settings tab and click OK to go back to the Internet Protocol TCP/IP Properties screen. 7. 8. Click OK to close the Internet Protocol (TCP/IP) Properties window. Click OK to close the Local Area Connection Properties window. Checking/Updating Your Computer's IP Address 1. In the computer, click Start, (All) Programs, Accessories and then Command Prompt. In the Command Prompt window, type "ipconfig" and then press ENTER to verify that your computer's IP address is in the correct range (192. 168. 1. 2 to 192. 168. 1. 254) with subnet mask 255. 255. 255. 0. This is necessary in order to communicate with the Prestige. Refer to your User's Guide for detailed IP address configuration for other Windows and Macintosh computer operating systems. Configuring Your Prestige Choose one of these methods to access and configure the Prestige. This Quick Start Guide shows you how to use the web configurator wizard only. See your User's Guide for background information on all Prestige features and SMT configuration. Click the web configurator online help for screen-specific web help. Web Configurator SMT (System Management Terminal). Access the SMT via: o o Console port using terminal emulation software LAN or WAN using Telnet 6 Prestige 791R Accessing Your Prestige Via Web Configurator Step 1. Enter "192. 168. 1. 1" as the web site address. Web site address. Step 2. The default password ("1234") is already in the password field (in non-readable format). Click Login to proceed to a screen asking you to change your password. Click Reset to revert to the default password in the password field. Default user name. Step 3. You should now see the web configurator Site Map screen. Click Wizard Setup to begin a series of screens to configure your Prestige for the first time. Click a link under Advanced Setup to configure advanced Prestige features. Click a link under Maintenance to see Prestige performance statistics, upload firmware and back up, restore or upload a configuration file. Click Logout in the navigation panel when you have finished a Prestige management session. 7 Prestige 791R WIZARD NAVIGATION PANEL LOGOUT The Prestige automatically logs you out if it is left idle for five minutes; press ENTER to log back in again. Internet Access Using the Wizard Use the Wizard Setup screens to configure your system for Internet access settings and fill in the fields with the information in the Internet Account Information table. Your ISP may have already configured some of the fields in the wizard screens for you. In the Site Map screen click Wizard Setup to display the first wizard screen. 8 Prestige 791R Select Client if your Prestige will act as a client device or Server if your Prestige will act as a server. If you enable Rate Adaption, the Prestige will connect at the optimal transfer rate between the min and max rates below. [. . . ] See Internet Connection with PPPoA for information on the remaining fields. Internet Connection with PPPoE Enter a subnet mask in dotted decimal notation in the Subnet Mask field. In the ENET ENCAP Gateway field, enter the gateway IP address given by your ISP. See Internet Connection with PPPoA for information on the remaining fields. Internet Connection with ENET ENCAP 11 Prestige 791R Type your ISP-assigned static IP address in the IP Address field. See Internet Connection with PPPoA for information on Network Address Translation. Internet Connection with RFC1483 Step 4. This screen will not be shown when the Prestige is in bridge mode. [. . . ]