User manual ZYXEL PRESTIGE 650H-13

[. . . ] Prestige 650H ADSL Router User's Guide Version 3. 40 May 2002 Prestige 650H ADSL Router Copyright Copyright © 2002 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. [. . . ] These are the mapping types discussed in Table 7-2. Server allows you to specify multiple servers of different types behind NAT to this computer. Only local IP fields are N/A for server; Global IP fields MUST be set for Server. This is the starting local IP address (ILA). This is the ending local IP address (ILA). If the rule is for all local IPs, then put the Start IP as 0. 0. 0. 0 and the End IP as 255. 255. 255. 255. This field is N/A for One-to-One and Server types. 0. 0. 0. 0 N/A EXAMPLE One-to-One Local IP Start End Global IP Start This is the starting global IP address (IGA). If you have a dynamic IP, enter 0. 0. 0. 0 as the Global IP Start. Note that Global IP Start can be set to 0. 0. 0. 0 only if the types are Many-to-One or Server. This is the ending global IP address (IGA). This field is N/A for One-to-One, Many-to-One and Server types. Only available when Type is set to Server. Type a number from 1 to 10 to choose a server set from menu 15. 2. 0. 0. 0. 0 End Server Mapping St N/A NAT 7-13 Prestige 650H ADSL Router FIELD Server Mapping Set DESCRIPTION Only available when Type is set to Server. Type a number from 1 to 10 to choose a server set from menu 15. 2. EXAMPLE Once you have finished configuring a rule in this menu, press [ENTER] at the message "Press ENTER to Confirm. . . " to save your configuration, or press [ESC] to cancel. 7. 4 NAT Server Sets ­ Port Forwarding A NAT server set is a list of inside (behind NAT on the LAN) servers, for example, web or FTP, that you can make visible to the outside world even though NAT makes your whole inside network appear as a single machine to the outside world. Use Menu 15 - NAT Setup to forward incoming service requests to the server(s) on your local network. You may enter a single port number or a range of port numbers to be forwarded, and the local IP address of the desired server. The port number identifies a service; for example, web service is on port 80 and FTP on port 21. In some cases, such as for unknown services or where one server can support more than one service (for example both FTP and web service), it might be better to specify a range of port numbers. In addition to the servers for specified services, NAT supports a default server. [. . . ] 10-1 System Maintenance 10-1, 10-3, 11-2, 11-4, 11-6, 11-7, 11-9, 12-1, 12-2, 12-4 System Management Terminal . . . . . . . . . . . . . . . . . . . . . . 2-10 System Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 System Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3 T TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1, 8-16, 10-8, 15-1 TCP/IP Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]