User manual ZYXEL PRESTIGE 334 QUICK GUIDE

[. . . ] Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice. Trademarks Trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners. ii Prestige 100 and 100IH ISDN Router and Router/Hub The declarations of CE marking: The Prestige 100 and 100IH has been approved for connection to the Public Switched Telecommunication Network using interfaces compatible with ITU-TSS recommendation I. 420 (Basic Rate ISDN user access). The Prestige 100 and 100IH comply with the following directives: 1. [. . . ] CHAP/PAP CHAP PAP Enable Disable Outgoing: Outgoing: Your Prestige always calls this remote node using the Primary Phone number first for a dial-up line. If the Primary Phone number is busy or does not answer, your Prestige will dial the Secondary Phone number if available. Some areas require dialing the pound sign # before the phone number for local calls. A # symbol may be included at the beginning of the phone numbers as required. Edit PPP Options To edit the PPP options for this remote node, move the cursor to this field, use the space bar to select Yes and press [Enter]. This will bring you to Menu 11. 2 - Remote Node PPP Options. For more information on configuring PPP options, see the section Editing PPP Options. This is a required field [?] if Route is set to IP. Enter the IP address of the remote gateway. Press space bar to toggle Yes then press [Enter] Rem IP Addr 4-4 Remote Node Configuration Prestige 100 and 100IH ISDN Router and Router/Hub Telco Options: Allocated Budget (min) Period (hr) Transfer Type This field sets a ceiling for outgoing call time for this remote node. The default for this field is 0 for no budget control. This field sets the time interval to reset the above outgoing call budget control. This field specifies the type of connection between the Prestige and this remote node. The range is 30 to 64 Kbps (kilobits per second). The parameters are separated by a `-'. For example, `30-60' means the add threshold is 30 Kbps and subtract threshold is 60 Kbps. The Prestige performs bandwidth on demand only if it initiates the call. 4-6 Remote Node Configuration Prestige 100 and 100IH ISDN Router and Router/Hub Addition and subtraction are based on the value set in the BOD Calculation field. If this field is set to Transmit or Receive, then traffic in either direction will be included to determine if a link should be added or dropped. Transmit will only use outgoing traffic to make this determination and Receive will only use incoming traffic to make this determination. If, after making the call to bring up a second channel, the second channel does not succeed in joining the Multilink Protocol bundle (because the remote device does not recognize the second call as coming from the same device), the Prestige will hang up the second call and continue with the first channel alone. The BOD configuration is through Menu 11. 2 - Remote Node PPP Options. 4. 1. 5 Editing PPP Options To edit the remote node PPP Options, move the cursor to the Edit PPP Options field in Menu 11. 1 - Remote Node Profile, and use the space bar to select Yes. Press Enter to open Menu 11. 2, as shown below. Menu 11. 2 - Remote Node PPP Options Encapsulation= Standard PPP Compression= No Multiple Link Options: BOD Calculation= Transmit or Receive Base Trans Rate(Kbps)= 64 Max Trans Rate(Kbps)= 64 Target Utility(Kbps)= 32-48 Add Persist(sec)= 5 Subtract Persist(sec)= 5 Press ENTER to CONFIRM or ESC to CANCEL: Press Space Bar to Toggle. Figure 4-3 Menu 11. 2 - Remote Node PPP Options The following table describes the Remote Node PPP Options Menu, and contains instructions on how to configure the PPP options fields. Remote Node Configuration 4-7 Prestige 100 and 100IH ISDN Router and Router/Hub Table 4-3 Remote Node PPP Options Menu Fields Field Encapsulation Description Select the CISCO PPP only when this remote node is a Cisco machine; otherwise, select the Standard PPP. Option Standard PPP CISCO PPP On/Off (Default = Off) Compression Turn on/off Stac Compression. The default for this field is Off. Multiple Link Options: BOD Calculation Select the direction of the traffic you wish to use in determining when to add or subtract a link. [. . . ] If the code is 1, the ISDN link is not up. This problem could be either the ISDN line is not properly connected to the Prestige or the ISDN line is not activated. Verify that the ISDN line is connected to the Prestige and to the wall telephone jack. If the code is 2, there is a SPID error (North America only). [. . . ]