User manual ZYXEL SP-200E INSTALLATION

[. . . ] This LED comes on when there is a 100 Mbps connection and blinks when sending or receiving traffic. This LED comes on when there is a 10 Mbps connection and blinks when sending or receiving traffic. PS/2 keypad port Connect an optional PS/2 keypad to this port. Refer to the hotspot gateway User's Guide for information on how to configure the gateway for use with the SP-200E and the optional PS/ 2 keypad. 3 SP-200E User's Start Guide 2. 3 Front Panel Push-Buttons Push the power switch to ON. The buttons on the front panel light up when the statement printer is receiving power. [. . . ] Enter the port number that the SP-200E uses when communicating with the hotspot or service gateway. The hotspot or service gateway must also use the same port number. Turn on the encryption to encode the communications between the SP-200E and the hotspot or service gateway. When you use the encryption, the data is unreadable to anyone that does not know the secret key. This protects against people stealing account information or creating illegitimate accounts. To use encryption, you must also configure the secret key in the following field and on the hotspot or service gateway. When you use encryption, enter a code here. You must also configure the same code as the secret key on the hotspot or service gateway. Enter a new password for accessing the SP-200E. Make sure you keep your password in a safe place. If you lose or forget it, you will need to press the RST (reset) button on the SP-200E rear panel to restore the default settings. Retype your password to make sure you have entered it correctly. Click Apply to save the changes. Subnet Mask Destination IP address Port Encryption Secret key Apply Renew Password Confirm Password Apply 4. 3 Firmware Upload To upgrade the firmware, you first have to download the latest firmware from www. zyxel. com and then use the web configurator to upload it to the SP-200E. The firmware will include the device name (SP200E) and end with a . bin extension. 7 SP-200E User's Start Guide After you enter the user name and password and click Firmware Upgrade in the login screen, you need to wait a moment and click Continue to display the Firmware Upgrade screen. Specify the name of the firmware file in the Local PC File Path field or click Browse to locate the file and click Apply to start the file transfer process. The firmware must be a binary file and should have a . bin extension. Note: WARNING!Do not close the browser or disconnect or turn off the SP-200E, as interrupting the file upload process may PERMANENTLY damage the device. When the upgrade is completed successfully, click Re Login to return to the login screen where you can check the firmware version. 5 Specifications Table 4 Specifications Power Adapter Power Adapter Input Voltage Power Adapter Output Power Power Consumption Power Over Ethernet (POE) Front Interfaces Back Panel Interfaces Printing method Recommended Thermal Paper MUT15-050250 AC 100 ~ 240 Volts 5V, 2. 5A 12 Watts Max. Compatible with mid-span Power Over Ethernet (PoE) injectors (receives power on pins 4, 5, 7 and 8) 3 Button x 3 Reset button, Power switch, DC power input socket, RJ-45 port, PS/2 port Direct thermal FD410 8 SP-200E User's Start Guide Paper Width Printing Width Paper Length Number of Statements Per Paper Roll Paper Roll Outside Diameter Paper Roll Inside Diameter Printing Speed Dot Resolution Dot Configuration Paper Detection Thermal Head Service Life Paper Thickness Dot Resolution Communication Interface 58(+0/-1) mm 48 mm 50 m max. A single account statement is around 15 cm in length. You should be able to print about 333 account statements on a 50 m paper roll. 63(+2/-2) mm 12(+0. 5/-0) mm 25. 4 mm / second 8 dots / mm (203 dpi) 384 dots / line Photo interrupter 108 pulses or 50 Km 65 um 8 (dots / mm) (203 dpi) Ethernet port (RJ-45) LED on port 100 Mbps Link/ACT, yellow, 10 Mbps Link/ACT, green Supported Protocols: ARP, IP, ICMP, UDP, TCP, HTTP Communication Cable Type Communication Cable Length PS/2 Keypad Interface PS/2 Keypad Interface Acceptable Characters Dimensions Operating Temperature Storage Temperature Operational Humidity Storage Humidity Certification Ethernet up to 100 meters PS/2 port for optional 16 Key, PS/2 keypad 0123456789+*/. "Enter" 109(W) × 155(D) × 90(H) mm 0 to 50 degrees Celsius -20 to 60 degrees Celsius 10 ~ 80 RH (non condensing) 10 ~ 95 RH (non condensing) VCCI, C-Tick, CE, FCC, CSA 9 SP-200E User's Start Guide 6 Troubleshooting Table 5 Troubleshooting Problem The push-button LEDs are off. Corrective Action Make sure that you have the correct power adaptor connected to the printer and plugged in to an appropriate power source. [. . . ] · Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution. · If the power adaptor or cord is damaged, remove it from the power outlet. 10 SP-200E User's Start Guide · Never disassemble the printer or the adapter. · Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one. [. . . ]