User manual ZYXEL XGS-4528F

[. . . ] XGS-4528F Intelligent Layer 3+ Switch User's Guide Version 3. 80 8/2007 Edition 1 DEFAULT LOGIN IP Address http://192. 168. 1. 1 User Name admin Password 1234 www. zyxel. com About This User's Guide About This User's Guide Intended Audience This manual is intended for people who want to configure the Switch using the web configurator or via commands. You should have at least a basic knowledge of TCP/IP networking concepts and topology. Related Documentation · Quick Start Guide The Quick Start Guide contains information on setting up your hardware. · Web Configurator Online Help Embedded web help for descriptions of individual screens and supplementary information. It is recommended you use the web configurator to configure the Switch. · Supporting Disk Refer to the included CD for support documents. [. . . ] Click Advanced Application > Classifier in the navigation panel to display the configuration screen as shown. XGS-4528F User's Guide 151 Chapter 18 Classifier Figure 72 Advanced Application > Classifier The following table describes the labels in this screen. Table 44 Advanced Application > Classifier LABEL Active Name Packet Format DESCRIPTION Select this option to enable this rule. Enter a descriptive name for this rule for identifying purposes. Choices are All, 802. 3 tagged, 802. 3 untagged, Ethernet II tagged and Ethernet II untagged. A value of 802. 3 indicates that the packets are formatted according to the IEEE 802. 3 standards. A value of Ethernet II indicates that the packets are formatted according to RFC 894, Ethernet II encapsulation. Layer 2 Specify the fields below to configure a layer 2 classifier. VLAN Priority Select Any to classify traffic from any VLAN or select the second option and specify the source VLAN ID in the field provided. Select Any to classify traffic from any priority level or select the second option and specify a priority level in the field provided. 152 XGS-4528F User's Guide Chapter 18 Classifier Table 44 Advanced Application > Classifier (continued) LABEL Ethernet Type Source MAC Address Port Destination MAC Address Select Any to apply the rule to all MAC addresses. To specify a destination, select the second choice and type a MAC address in valid MAC address format (six hexadecimal character pairs). Select Any to apply the rule to all MAC addresses. To specify a source, select the second choice and type a MAC address in valid MAC address format (six hexadecimal character pairs). Type the port number to which the rule should be applied. You may choose one port only or all ports (Any). DESCRIPTION Select an Ethernet type or select Other and enter the Ethernet type number in hexadecimal value. Refer to Table 46 on page 154 for information. Layer 3 Specify the fields below to configure a layer 3 classifier. DSCP IP Protocol Select Any to classify traffic from any DSCP or select the second option and specify a DSCP (DiffServ Code Point) number between 0 and 63 in the field provided. Select an IP protocol type or select Other and enter the protocol number in decimal value. Refer to Table 47 on page 155 for more information. You may select Establish Only for TCP protocol type. This means that the Switch will pick out the packets that are sent to establish TCP connections. Enter a source IP address in dotted decimal notation. Specify the address prefix by entering the number of ones in the subnet mask. Source IP Address/ Address Prefix Socket Number Note: You must select either UDP or TCP in the IP Protocol field before you configure the socket numbers. Select Any to apply the rule to all TCP/UDP protocol port numbers or select the second option and enter a TCP/UDP protocol port number. Destination IP Address/ Address Prefix Socket Number Enter a destination IP address in dotted decimal notation. Specify the address prefix by entering the number of ones in the subnet mask. Note: You must select either UDP or TCP in the IP Protocol field before you configure the socket numbers. Select Any to apply the rule to all TCP/UDP protocol port numbers or select the second option and enter a TCP/UDP protocol port number. Add Click Add to insert the entry in the summary table below and save your changes to the Switch's run-time memory. [. . . ] Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value, and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. Note Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. [. . . ]