User manual ZYXEL XGS4700-48F

[. . . ] XGS4700-48F Layer 3 Managed Stackable Gigabit Ethernet Switch Default Login Details IP Address http://192. 168. 0. 1 (Out-of-band MGMT port) http://192. 168. 1. 1 (In-band ports) User Name Password admin 1234 Firmware Version 4. 00 Edition 1, 04/2011 www. zyxel. com www. zyxel. com Copyright © 2011 ZyXEL Communications Corporation About This User's Guide About This User's Guide Intended Audience This manual is intended for people who want to configure the Switch using the web configurator. Related Documentation · Web Configurator Online Help The embedded Web Help contains descriptions of individual screens and supplementary information. · Command Reference Guide The Command Reference Guide explains how to use the Command-Line Interface (CLI) and CLI commands to configure the Switch. Note: It is recommended you use the web configurator to configure the Switch. · Support Disc Refer to the included CD for support documents. Documentation Feedback Send your comments, questions or suggestions to: techwriters@zyxel. com. tw Thank you!The Technical Writing Team, ZyXEL Communications Corp. , 6 Innovation Road II, Science-Based Industrial Park, Hsinchu, 30099, Taiwan. Need More Help? More help is available at www. zyxel. com. XGS4700-48F User's Guide 3 About This User's Guide · Download Library Search for the latest product updates and documentation from this link. Read the Tech Doc Overview to find out how to efficiently use the User Guide, Quick Start Guide and Command Line Interface Reference Guide in order to better understand how to use your product. [. . . ] In order to support VLAN stacking on a port, the port must be able to allow frames of 1526 Bytes (1522 Bytes + 4 Bytes for the second tag) to pass through it. Tunnel TPID TPID is a standard Ethernet type code identifying the frame and indicates whether the frame carries IEEE 802. 1Q tag information. Enter a four-digit hexadecimal number from 0000 to FFFF that the Switch adds in the outer VLAN tag of the frames sent on the tunnel port(s). The Switch also uses this to check if the received frames are double-tagged. The value of this field is 0x8100 as defined in IEEE 802. 1Q. If the Switch needs to communicate with other vendors' devices, they should use the same TPID. Note: You can define up to four different tunnel TPIDs (including 8100) in this screen at a time. Apply Click Apply to save your changes to the Switch's run-time memory. The Switch loses these changes if it is turned off or loses power, so use the Save link on the top navigation panel to save your changes to the non-volatile memory when you are done configuring. Click Cancel to begin configuring this screen afresh. Cancel 23. 4. 1 Port-based Q-in-Q Port-based Q-in-Q lets the Switch treat all frames received on the same port as the same VLAN flows and add the same outer VLAN tag to them, even they have different customer VLAN IDs. XGS4700-48F User's Guide 225 Chapter 23 VLAN Stacking Click Port-based QinQ in the Advanced Application > VLAN Stacking screen to display the screen as shown. Figure 101 Advanced Application > VLAN Stacking > Port-based QinQ The following table describes the labels in this screen. Table 60 Advanced Application > VLAN Stacking > Port-based QinQ LABEL Port SPVID DESCRIPTION The port number identifies the port you are configuring. SPVID is the service provider's VLAN ID (the outer VLAN tag). Enter the service provider ID (from 1 to 4094) for frames received on this port. See Chapter 9 on page 119 for more background information on VLAN ID. This is the service provider's priority level that adds to the frames received on this port. "0" is the lowest priority level and "7" is the highest. Priority Apply Click Apply to save your changes to the Switch's run-time memory. The Switch loses these changes if it is turned off or loses power, so use the Save link on the top navigation panel to save your changes to the non-volatile memory when you are done configuring. Click Cancel to begin configuring this screen afresh. Cancel 23. 4. 2 Selective Q-in-Q Selective Q-in-Q is VLAN-based. It allows the Switch to add different outer VLAN tags to the incoming frames received on one port according to their inner VLAN tags. 226 XGS4700-48F User's Guide Chapter 23 VLAN Stacking Note: Selective Q-in-Q rules are only applied to single-tagged frames received on the access ports. If the incoming frames are untagged or single-tagged but received on a tunnel port or cannot match any selective Q-in-Q rules, the Switch applies the port-based Q-in-Q rules to them. Click Selective QinQ in the Advanced Application > VLAN Stacking screen to display the screen as shown. Figure 102 Advanced Application > VLAN Stacking > Selective QinQ The following table describes the labels in this screen. Table 61 Advanced Application > VLAN Stacking > Selective QinQ LABEL Active Name Port CVID SPVID DESCRIPTION Check this box to activate this rule. Enter a descriptive name (up to 32 printable ASCII characters) for identification purposes. The port number identifies the port you are configuring. Enter a customer VLAN ID (the inner VLAN tag) from 1 to 4094. This is the VLAN tag carried in the packets from the subscribers. SPVID is the service provider's VLAN ID (the outer VLAN tag). [. . . ] This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this device in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CE Mark Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Taiwanese BSMI (Bureau of Standards, Metrology and Inspection) A Warning: Notices Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This Class A digital apparatus complies with Canadian ICES-003. [. . . ]